Ransomes HR380 Скачать руководство пользователя

Страница: 121 / 128

en-121

QUALITY OF CUT 12

12.9

INCONSISTENT UNCUT PATCHES _________________________________

“Insufficient Mulching.” This problem is identified by

long lengths of random clumps of uncut grass.

Possible Cause

Correction

Damaged or missing blades.

Check and replace damaged blades or try

Eliminator blades.

Extreme volume of grass is not discharged quickly

enough from the deck.

Consider using a cut and clear kit

(152cm rotary deck only).

Cutting at more than the recommended speed.

Decrease the cutting speed.

The Height of grass is being reduced by too much in

one pass.

Mow more often or raise the height of cut.

Incorrect deck rake angle.

Ensure the rear of the deck is set correctly. Then if

issue persists increase the rake angle by raising the

rear of the deck by one hole.

Poor ground following due to ground undulations.

Cut in different direction.

TN1278

Содержание HR380

































































































































Результаты поиска

Содержание HR380

Отзывы:

Похожие инструкции для HR380

Бренды по названию

Популярные бренды

Ransomes HR380, Руководство пользователя

Результаты поиска

Содержание HR380

Отзывы:

Похожие инструкции для HR380

Бренды по названию

Популярные бренды