Ransomes HR380 Скачать руководство пользователя страница 74

Страница: 74 / 128

en-74

8 MAINTENANCE AND LUBRICATION

8.1.5

REPLACEMENT ______________________________________________________

8.1.6

SKIDS ______________________________________________________________

Screws

Safety cover

Bolt

Tensioning

Release

Lock nuts

Counter-
weight

Bolt

V-belt

Screws

Skid

If there are any tears or other damage on the V-belt, it

must be replaced.

•

Remove the screws, remove the safety cover.

•

Loosen the lock nuts.

•

Use the bolt to slacken the V-belt tension.

The V-belt unit consists of two narrow V-belts.

•

Fit the new V-belts

•

Check the V-belt for correct positioning

•

Tension the V-belt

•

Reassemble the safety cover

The Skids protect the machine from direct contact with

the ground. If they are not replaced in good time, the

housing of the machine will be damaged. There are

Skids on the right-hand side and left-hand side.

•

Undo nuts, remove screws and washers.

•

Remove old skid

•

Fit new runner

•

Fit new screws and washers

•

Secure screws with new nuts

Содержание HR380

































































































































Результаты поиска

Содержание HR380

Отзывы:

Бренды по названию

Популярные бренды

Ransomes HR380, Руководство пользователя

Результаты поиска

Содержание HR380

Отзывы:

Бренды по названию

Популярные бренды