Ransomes HR380 Скачать руководство пользователя страница 46

Страница: 46 / 128

en-46

6 CONTROLS

6.6 WARNING SCREENS__________________________________________________

When malfunctions occur, the following warning screens are displayed.

6.6.1 SLOPE ANGLE DISPLAY______________________________________________

During work, if the machine is driven on a slope of 16° the machine angle

will be displayed in the centre of the screen, until the machine has been

driven onto an area of less than 16°.

6.6.2 WARNING MAXIMUM SLOPE ANGLE EXCEEDED _________________________

If the slope angle reaches 19° the screen will display this warning to indi

cate that the machine’s safe working angle has been reached.

6.6.3 WARNING SLOPE ANGLE – INHIBIT LIFT ________________________________

If the slope angle reaches 21° the screen will display this warning which

indicates that the cutters will be prevented from starting if not already run

ning, or re-started if running then stopped. An audible warning will be

sounded four times at 4 second intervals, and the red LEDs will flash four

times at 4 second intervals. This will continue until the machine has been

driven to an area of less than 19°.

1234

123.4 Hours

1/1

Содержание HR380

































































































































Результаты поиска

Содержание HR380

Отзывы:

Бренды по названию

Популярные бренды

Ransomes HR380, Руководство пользователя

Результаты поиска

Содержание HR380

Отзывы:

Бренды по названию

Популярные бренды