RAM Commercial Chassis Cab 2017 Скачать руководство пользователя | Manualshive

Страница: 466 / 542

background image

CAUTION!

(Continued)

•

If a “fast charger” is used while the battery is in the
vehicle, disconnect both vehicle battery cables before
connecting the charger to the battery. Do not use a
“fast charger” to provide starting voltage.

Air Conditioner Maintenance

For best possible performance, your air conditioner should
be checked and serviced by an authorized dealer at the
start of each warm season. This service should include
cleaning of the condenser fins and a performance test.
Drive belt tension should also be checked at this time.

WARNING!

•

Use only refrigerants and compressor lubricants ap-
proved by the manufacturer for your air conditioning
system. Some unapproved refrigerants are flam-
mable and can explode, injuring you. Other unap-
proved refrigerants or lubricants can cause the sys-
tem to fail, requiring costly repairs. Refer to
Warranty Information Book for further warranty
information.

(Continued)

WARNING!

(Continued)

•

The air conditioning system contains refrigerant un-
der high pressure. To avoid risk of personal injury or
damage to the system, adding refrigerant or any
repair requiring lines to be disconnected should be
done by an experienced technician.

CAUTION!

Do not use chemical flushes in your air conditioning
system as the chemicals can damage your air condition-
ing components. Such damage is not covered by the
New Vehicle Limited Warranty.

Refrigerant Recovery And Recycling R134a — If
Equipped

R-134a Air Conditioning Refrigerant is a hydrofluoro-
carbon (HFC) that is an ozone-saving product. However,
the manufacturer recommends that air conditioning ser-
vice be performed by authorized dealer or other service
facilities using recovery and recycling equipment.

NOTE:

Use only manufacturer approved A/C system PAG

compressor oil and refrigerants.

464

MAINTAINING YOUR VEHICLE

«
...
464
465
466
467
468
...
»

Содержание Chassis Cab 2017































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Chassis Cab 2017

Бренд: Accel Страницы: 2

Бренд: Federal Signal Corporation Страницы: 8

Бренд: Federal Signal Corporation Страницы: 8

Бренд: Jeep Страницы: 603

Бренд: Jeep Страницы: 80

PRIME DESIGN VCR 326

Бренд: Safe Fleet Страницы: 16

Prime Design VBC PC11

Бренд: Safe Fleet Страницы: 8

Prime Design AR1418

Бренд: Safe Fleet Страницы: 4

Бренд: JANE Страницы: 21

Бренд: Chariot Carriers Страницы: 3

Бренд: Rola Страницы: 3

Бренд: Caltrend Страницы: 2

Бренд: Audiovox Страницы: 1

EGR-3PVE-COLOUR

Бренд: EGR Страницы: 28

Carpower CAP-20

Бренд: Monacor Страницы: 2

Бренд: Honda Страницы: 20

2009 Rio Series

Бренд: Kia Страницы: 219

Бренд: JKS Страницы: 3

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды