RAM Commercial Chassis Cab 2017 Скачать руководство пользователя страница 396 | Manualshive

Страница: 396 / 542

background image

CAUTION!

(Continued)

the asymmetrical design (tread pattern) of the On/
Off road tire.

•

When replacing a flat, the spare tire may have to be
remounted on the rim or installed at a different
location to maintain the correct placement of the tire
on the wheel relative to the tire/wheel position on
the vehicle. For example, if the spare is used to
replace an outer rear tire it will have to be remounted
on the rim so that the wheel is dished inward. That
way the tread design of asymmetrical tires will
maintain proper position.

DEPARTMENT OF TRANSPORTATION UNIFORM
TIRE QUALITY GRADES

The following tire grading categories were established
by the National Highway Traffic Safety Administration.
The specific grade rating assigned by the tire’s manu-
facturer in each category is shown on the sidewall of the
tires on your vehicle.

All passenger vehicle tires must conform to Federal
safety requirements in addition to these grades.

Treadwear

The Treadwear grade is a comparative rating, based on
the wear rate of the tire when tested under controlled
conditions on a specified government test course. For
example, a tire graded 150 would wear one and one-half
times as well on the government course as a tire graded
100. The relative performance of tires depends upon the
actual conditions of their use, however, and may depart
significantly from the norm due to variations in driving
habits, service practices, and differences in road charac-
teristics and climate.

Traction Grades

The Traction grades, from highest to lowest, are AA, A,
B, and C. These grades represent the tire’s ability to stop
on wet pavement, as measured under controlled condi-
tions on specified government test surfaces of asphalt
and concrete. A tire marked C may have poor traction
performance.

WARNING!

The traction grade assigned to this tire is based on
straight-ahead braking traction tests, and does not

(Continued)

394

STARTING AND OPERATING

«
...
394
395
396
397
398
...
»

Содержание Chassis Cab 2017































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Chassis Cab 2017

witty park XEV6 Series

Бренд: hager Страницы: 9

Indigo MANZA QUADRAJET 90

Бренд: TATA Motors Страницы: 10

Бренд: Ecco Страницы: 9

Бренд: Fast Master Products Страницы: 13

XEBRA ZAPCAR Series

Бренд: Zap Страницы: 16

Бренд: Westin Страницы: 3

Бренд: Weltmann KFZ-Teile Страницы: 12

Бренд: iDataLink Страницы: 6

2917 Nstallation

Бренд: Edelbrock Страницы: 1

Бренд: Anker Technology Страницы: 8

Бренд: TOPPOINT Страницы: 2

Бренд: Whispbar Страницы: 63

Бренд: Mopar Страницы: 18

Бренд: Dometic Страницы: 24

F-250 Super Duty 2022

Бренд: Ford Страницы: 740

Бренд: Rugged Ridge Страницы: 5

Giulietta 2.0 JTDM

Бренд: Alfa Romeo Страницы: 14

Бренд: Gator Страницы: 5

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды