RAM Commercial Chassis Cab 2017 Скачать руководство пользователя страница 350 | Manualshive

Страница: 350 / 542

background image

NOTE:

Before retrying a selection, make certain that all

the necessary requirements for selecting a new transfer
case position have been met. To retry the selection, turn the
control switch back to the current position, wait five
seconds, and retry selection. To find the shift requirements,
refer to the

⬙

Shifting Procedure

⬙

for your transfer case,

located in this section.

The “SVC 4WD Warning Light” monitors the electronic
shift four-wheel drive system. If this light remains on after
engine start up or illuminates during driving, it means that
the four-wheel drive system is not functioning properly
and that service is required.

WARNING!

Always engage the parking brake when powering
down the vehicle if the “SVC 4WD Warning Light” is
illuminated. Not engaging the parking brake may
allow the vehicle to roll, which may cause personal
injury.

NOTE:

Do not attempt to make a shift while only the front

or rear wheels are spinning, as this can cause damage to
driveline components.

When operating your vehicle in 4WD LOW, the engine
speed is approximately three times that of the 2WD or
4WD LOCK positions at a given road speed. Take care not
to overspeed the engine and do not exceed 25 mph
(40 km/h).

Proper operation of four-wheel drive vehicles depends on
tires of equal size, type and circumference on each wheel.
Any difference in tire size can cause damage to the
drivetrain.

Because four-wheel drive provides improved traction,
there is a tendency to exceed safe turning and stopping
speeds. Do not go faster than road conditions permit.

WARNING!

You or others could be injured or killed if you leave the
vehicle unattended with the transfer case in the NEU-
TRAL position without first fully engaging the park-
ing brake. The transfer case NEUTRAL position disen-
gages both the front and rear drive shafts from the
powertrain and will allow the vehicle to roll, even if
the transmission is in PARK. The parking brake
should always be applied when the driver is not in the
vehicle.

348

STARTING AND OPERATING

«
...
348
349
350
351
352
...
»

Содержание Chassis Cab 2017































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Chassis Cab 2017

Бренд: Roav Страницы: 10

10-8002-C11998B

Бренд: Saleen Страницы: 12

2013 Buick Verano

Бренд: Buick Страницы: 5

Бренд: Yakima Страницы: 8

Бренд: Porsche Страницы: 313

Бренд: STO N SHO Страницы: 7

Dodge Challenger SRT8®Challenger SRT8 392 2012

Бренд: Dodge Страницы: 5

Бренд: Edelbrock Страницы: 2

Бренд: Meta System Страницы: 16

BASIC TLL171231

Бренд: Tellur Страницы: 5

Бренд: Rugged Ridge Страницы: 3

Alloy Rugged Ridge X-Clamp

Бренд: Omix-Ada Страницы: 2

Бренд: Dodge Страницы: 3

Бренд: Havis Страницы: 5

Multi Vehicle Mount MVM-35-05

Бренд: Bracketron Страницы: 4

Бренд: Yenkee Страницы: 22

Бренд: MiX Telematics Страницы: 39

Бренд: PEUGEOT Страницы: 404

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды