RAM Commercial Chassis Cab 2017 Скачать руководство пользователя страница 168 | Manualshive

Страница: 168 / 542

background image

Before You Begin Programming HomeLink

Ensure your vehicle is parked outside of the garage before
you begin programming.

For efficient programming and accurate transmission of
the radio-frequency signal it is recommended that a new
battery be placed in the hand-held transmitter of the device
that is being programmed to the HomeLink system.

To erase the channels place the ignition in the ON/RUN
position and push and hold the two outside HomeLink
buttons (I and III) for up to 20 seconds. The instrument
cluster display will display “CLEARING CHANNELS.”
Release the buttons when “CHANNELS CLEARED” ap-
pears on the display.

NOTE:

•

For vehicle’s equipped with Keyless Enter-N-Go, place
the ignition in the RUN position with the Engine ON.
Make sure while programming HomeLink with the
engine ON that your vehicle is outside of your garage, or
that the garage door remains open at all times.

•

Erasing all channels should only be performed when
programming HomeLink for the first time. Do not erase
channels when programming additional buttons.

•

If you have any problems, or require assistance, please
call toll-free 1-800-355-3515 or, on the Internet at
HomeLink.com for information or assistance.

Programming A Rolling Code

For programming garage door openers that were manufac-
tured after 1995. These garage door openers can be identi-
fied by the “LEARN” or “TRAIN” button located where
the hanging antenna is attached to the garage door opener.
It is NOT the button that is normally used to open and
close the door. The name and color of the button may vary
by manufacturer.

166

UNDERSTANDING THE FEATURES OF YOUR VEHICLE

«
...
166
167
168
169
170
...
»

Содержание Chassis Cab 2017































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Chassis Cab 2017

Бренд: Jeda Страницы: 8

Бренд: Jeep Страницы: 496

Бренд: Honda Страницы: 73

Бренд: GOgroove Страницы: 9

Wallbox eM4 Single

Бренд: ABL Страницы: 68

Бренд: Prorack Страницы: 14

Бренд: Raytel LLC Страницы: 40

Бренд: Opel Страницы: 254

Бренд: Audiovox Страницы: 24

Бренд: Mercedes-Benz Страницы: 2

Бренд: Westin Страницы: 2

Бренд: Mercedes-Benz Страницы: 39

Бренд: Hama Страницы: 4

Бренд: Volvo Страницы: 230

Бренд: MiX Telematics Страницы: 39

Бренд: SuperATV Страницы: 2

Бренд: Edelbrock Страницы: 2

Бренд: Honda Страницы: 5

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды