RAM Commercial Chassis Cab 2017 Скачать руководство пользователя | Manualshive

Страница: 387 / 542

background image

WARNING!

Do not use Summer tires in snow/ice conditions. You
could lose vehicle control, resulting in severe injury or
death. Driving too fast for conditions also creates the
possibility of loss of vehicle control.

Snow Tires

Some areas of the country require the use of snow tires
during the Winter. Snow tires can be identified by a
“mountain/snowflake” symbol on the tire sidewall.

If you need snow tires, select tires
equivalent in size and type to the origi-
nal equipment tires. Use snow tires only
in sets of four; failure to do so may
adversely affect the safety and handling
of your vehicle.

Snow tires generally have lower speed ratings than what
was originally equipped with your vehicle and should not
be operated at sustained speeds over 75 mph (120 km/h).
For speeds above 75 mph (120 km/h), refer to original
equipment or an authorized tire dealer for recommended
safe operating speeds, loading and cold tire inflation
pressures.

While studded tires improve performance on ice, skid and
traction capability on wet or dry surfaces may be poorer
than that of non-studded tires. Some states prohibit stud-
ded tires; therefore, local laws should be checked before
using these tire types.

Run Flat Tires — If Equipped

Run Flat tires allow you the capability to drive 50 miles
(80 km) at 50 mph (80 km/h) after a rapid loss of inflation
pressure. This rapid loss of inflation is referred to as the
Run Flat mode. A Run Flat mode occurs when the tire
inflation pressure is of/or below 14 psi (96 kPa). Once a
Run Flat tire reaches the Run Flat mode, it has limited
driving capabilities and needs to be replaced immediately.
A Run Flat tire is not repairable.

It is not recommended to drive a vehicle loaded at full
capacity, or to tow a trailer while a tire is in the Run Flat
mode.

See the tire pressure monitoring section for more informa-
tion.

5

STARTING AND OPERATING

385

«
...
385
386
387
388
389
...
»

Содержание Chassis Cab 2017































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Chassis Cab 2017

Бренд: Kargo Master Страницы: 13

Бренд: Kargo Master Страницы: 21

Бренд: Kargo Master Страницы: 4

Бренд: Calix Страницы: 5

Бренд: Subaru Страницы: 3

Бренд: Allen Sports Страницы: 2

Бренд: Axxess Страницы: 8

Бренд: SeaSucker Страницы: 9

Бренд: REVCAMUK Страницы: 4

Бренд: Toyota Страницы: 52

Бренд: TBC Страницы: 12

Бренд: Prorack Страницы: 14

OCTAVIA - TECHNICAL CHANGES 11-2009

Бренд: Skoda Страницы: 16

1506-PHX Cargo Plus

Бренд: Ranger design Страницы: 8

Бренд: AUTOTECH Страницы: 1

Бренд: Rugged Ridge Страницы: 3

Бренд: Cadillac Страницы: 20

Бренд: r.LiNK Страницы: 21

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды