RAM Commercial Chassis Cab 2017 Скачать руководство пользователя | Manualshive

Страница: 439 / 542

background image

Before raising the wheel off the ground, make sure that
the jack will not damage surrounding truck parts and
adjust the jack position as required.

NOTE:

If the jack will not lower by turning the dial

(thumbwheel) by hand, it may be necessary to use the jack
drive tube in order to lower the jack.

4. By rotating the wheel wrench clockwise, raise the ve-

hicle until the wheel just clears the surface.

WARNING!

Raising the vehicle higher than necessary can make the
vehicle unstable. It could slip off the jack and hurt
someone near it. Raise the vehicle only enough to
remove the tire.

5. Remove the wheel nuts and pull the wheel off. Install

the spare wheel and wheel nuts with the cone shaped
end of the nuts toward the wheel on single rear wheel
(SRW) models. On dual rear wheel models (DRW) the
lug nuts are a two-piece assembly with a flat face.
Lightly tighten the nuts. To avoid risk of forcing the
vehicle off the jack, do not fully tighten the nuts until the
vehicle has been lowered.

6. Using the wheel wrench, finish tightening the nuts

using a crisscross pattern. For the proper lug nut torque
specifications refer to “Wheel and Tire Torque Specifi-
cations” in this section. If in doubt about the correct
tightness, have them checked with a torque wrench by
your authorized dealer or at a service station.

Rear Jacking Location

6

WHAT TO DO IN EMERGENCIES

437

«
...
437
438
439
440
441
...
»

Содержание Chassis Cab 2017































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Chassis Cab 2017

Бренд: Camcar Страницы: 2

Бренд: Porsche Страницы: 51

Бренд: Whispbar Страницы: 14

Wireless Charging Station Universal

Бренд: BMW Страницы: 160

01 29 9 416 497

Бренд: BMW Страницы: 5

adaptiv mini ADVM-BM1

Бренд: Connects2 Страницы: 4

Бренд: KEKO Страницы: 13

Stealth 4191F Series

Бренд: Road Armor Страницы: 5

Бренд: Demco Страницы: 4

PRIME DESIGN HRR3-E-PM52

Бренд: Safe Fleet Страницы: 12

Бренд: Kia Страницы: 5

Cuda TriOptic 351014F Series

Бренд: Federal Signal Corporation Страницы: 4

Бренд: Kia Страницы: 216

Бренд: TERAFLEX Страницы: 18

Бренд: Genesis Страницы: 30

Бренд: Jotto Desk Страницы: 3

Бренд: LAS Страницы: 4

Бренд: LAS Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды