RAM Commercial Chassis Cab 2017 Скачать руководство пользователя | Manualshive

Страница: 297 / 542

background image

Operating Tips

NOTE:

Refer to the chart at the end of this section for

suggested control settings for various weather conditions.

Summer Operation

The engine cooling system must be protected with a
high-quality antifreeze coolant to provide proper corrosion
protection and to protect against engine overheating. OAT
coolant (conforming to MS.90032) is recommended.

Winter Operation

To ensure the best possible heater and defroster perfor-
mance, make sure the engine cooling system is functioning
properly and the proper amount, type, and concentration
of coolant is used. Use of the Air Recirculation mode
during Winter months is not recommended, because it may
cause window fogging.

Vacation/Storage

Before you store your vehicle, or keep it out of service (i.e.,
vacation) for two weeks or more, run the air conditioning
system at idle for about five minutes, in fresh air with the
blower setting on high. This will ensure adequate system
lubrication to minimize the possibility of compressor dam-
age when the system is started again.

Window Fogging

Vehicle windows tend to fog on the inside in mild, rainy
and/or humid weather. To clear the windows, select
Defrost or Mix mode and increase the front blower speed.
Do not use the Recirculation mode without A/C for long
periods, as fogging may occur.

Outside Air Intake

Make sure the air intake, located directly in front of the
windshield, is free of obstructions such as leaves. Leaves
collected in the air intake may reduce airflow, and if they
enter the plenum, they could plug the water drains. In
winter months, make sure the air intake is clear of ice,
slush, and snow.

Cabin Air Filter

The climate control system filters out dust and pollen from
the air. Contact your authorized dealer to service your
cabin air filter, and to have it replaced when needed.

4

UNDERSTANDING YOUR INSTRUMENT PANEL

295

«
...
295
296
297
298
299
...
»

Содержание Chassis Cab 2017































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Chassis Cab 2017

Бренд: iDataLink Страницы: 9

Бренд: JETBAG Страницы: 44

Бренд: Yakima Страницы: 4

CommCenter D1 Series

Бренд: Federal Signal Corporation Страницы: 16

Бренд: Axxess Страницы: 8

Бренд: Kia Страницы: 54

Бренд: Yakima Страницы: 11

Бренд: Jaeger Страницы: 13

Бренд: Calix group Страницы: 4

Бренд: Volvo Страницы: 123

Бренд: Porsche Страницы: 146

2000 Accord Sedan

Бренд: Honda Страницы: 320

Бренд: Tactik Страницы: 4

Бренд: banks Страницы: 76

Бренд: Mercedes-Benz Страницы: 493

Бренд: MiX Telematics Страницы: 39

Tipper Remote Kit

Бренд: Nugent Страницы: 21

2004 JR41 Stratus Sedan

Бренд: Dodge Страницы: 273

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды