RAM Commercial Chassis Cab 2017 Скачать руководство пользователя страница 424 | Manualshive

Страница: 424 / 542

background image

Snowplow Prep Package Model Availability

For Information about snowplow applications visit
www.ramtrucks.com or refer to the current Ram Body
Builders Guide.

1. The maximum number of occupants in the truck should

not exceed two.

2. The total GVWR or the Front GAWR or the Rear GAWR

should never be exceeded.

3. Cargo capacity will be reduced by the addition of

options or passengers, etc.

The loaded vehicle weight, including the snowplow sys-
tem, all aftermarket accessories, driver, passengers, op-
tions, and cargo, must not exceed either the Gross Vehicle
Weight (GVWR) or Gross Axle Weight (GAWR) ratings.
These weights are specified on the Safety Compliance
Certification Label on the driver’s side door opening.

NOTE:

Detach the snowplow when transporting passen-

gers.

Vehicle front end wheel alignment was set to specifications
at the factory without consideration for the weight of the
plow. Front end toe-in should be checked and reset if

necessary at the beginning and end of the snowplow
season. This will help prevent uneven tire wear.

The blade should be lowered whenever the vehicle is
parked.

Maintain and operate your vehicle and snowplow equip-
ment following the recommendations provided by the
specific snowplow manufacturer.

Over The Road Operation With Snowplow Attached

The blade restricts air flow to the radiator and causes the
engine to operate at higher than normal temperatures.
Therefore, when transporting the plow, angle the blade
completely and position it as low as road or surface
conditions permit. Do not exceed 40 mph (64 km/h). The
operator should always maintain a safe stopping distance
and allow adequate passing clearance.

Operating Tips

Under ideal snow plowing conditions, 20 mph (32 km/h)
should be maximum operating speed. The operator should
be familiar with the area and surface to be cleaned. Reduce
speed and use extreme caution when plowing unfamiliar
areas or under poor visibility.

422

STARTING AND OPERATING

«
...
422
423
424
425
426
...
»

Содержание Chassis Cab 2017































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Chassis Cab 2017

Бренд: UnderCover Страницы: 16

Бренд: Abarth Страницы: 176

Бренд: Mazda Страницы: 527

2008 Escalade EXT

Бренд: Cadillac Страницы: 496

Brute Strength 12057.0271

Бренд: Quadratec Страницы: 6

Бренд: EEZ RV Страницы: 31

Бренд: Van Guard Страницы: 3

Бренд: Simplicity Страницы: 10

Бренд: Camecho Страницы: 2

E60-82-007-02-10

Бренд: Eibach Страницы: 3

2005 JR41 Stratus

Бренд: Dodge Страницы: 293

Бренд: Veldo Teknoloji Страницы: 32

Бренд: Fab Fours Страницы: 21

ZapCharger Portable C1

Бренд: ZAPTEC Страницы: 20

Бренд: Honda Страницы: 22

Бренд: Mercedes-Benz Страницы: 494

2007 SLR Mclaren

Бренд: Mercedes-Benz Страницы: 425

Бренд: Volvo Страницы: 92

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды