RAM Commercial Chassis Cab 2017 Скачать руководство пользователя | Manualshive

Страница: 416 / 542

background image

Towing Requirements

To promote proper break-in of your new vehicle drivetrain
components the following guidelines are recommended:

CAUTION!

•

Do not tow a trailer at all during the first 500 miles
(805 km) the new vehicle is driven. The engine, axle
or other parts could be damaged.

•

Then, during the first 500 miles (805 km) that a trailer
is towed, do not drive over 50 mph (80 km/h) and do
not make starts at full throttle. This helps the engine
and other parts of the vehicle wear in at the heavier
loads.

WARNING!

Improper towing can lead to a collision. Follow these
guidelines to make your trailer towing as safe as
possible:

•

Make certain that the load is secured in the trailer
and will not shift during travel. When trailering
cargo that is not fully secured, dynamic load shifts
can occur that may be difficult for the driver to

(Continued)

WARNING!

(Continued)

control. You could lose control of your vehicle and
have a collision.

•

When hauling cargo or towing a trailer, do not
overload your vehicle or trailer. Overloading can
cause a loss of control, poor performance or damage
to brakes, axle, engine, transmission, steering, sus-
pension, chassis structure or tires.

•

Safety chains must always be used between your
vehicle and trailer. Always connect the chains to the
hook retainers of the vehicle hitch. Cross the chains
under the trailer tongue and allow enough slack for
turning corners.

•

Vehicles with trailers should not be parked on a
grade. When parking, apply the parking brake on the
tow vehicle. Put the tow vehicle transmission in
PARK. For four-wheel drive vehicles, make sure the
transfer case is not in NEUTRAL (N). Always block
or

ⴖ

chock

ⴖ

the trailer wheels.

•

GCWR must not be exceeded.

(Continued)

414

STARTING AND OPERATING

«
...
414
415
416
417
418
...
»

Содержание Chassis Cab 2017































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Chassis Cab 2017

Бренд: RAM Страницы: 292

Бренд: RAM Страницы: 116

Yamaha Rhino 660

Бренд: Yamaha Страницы: 3

Бренд: IBASE Technology Страницы: 100

S2000 Windscreen Camera Mount

Бренд: Modifry Products Страницы: 2

Бренд: Draw tite Страницы: 4

Бренд: EFILive Страницы: 25

Speed & Route Profiler

Бренд: Racelogic Страницы: 24

Бренд: Curtis Страницы: 6

Бренд: Prorack Страницы: 15

Бренд: Discount Car Stereo Страницы: 8

Бренд: Whispbar Страницы: 14

Бренд: Prorack Страницы: 13

Бренд: Prime Design Страницы: 12

Бренд: SIXTOL Страницы: 32

Gigaware 12-493

Бренд: Gigaware Страницы: 8

Бренд: Conrad Страницы: 8

Бренд: AA Products Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды