RAM Commercial Chassis Cab 2017 Скачать руководство пользователя страница 441 | Manualshive

Страница: 441 / 542

background image

CAUTION!

•

Use a pulling motion to remove the hub cap. Do not
use a twisting motion when removing the hub cap,
damage to the hub cap; finish may occur.

•

The rear hub caps on the dual rear wheel has two
pull off notches. Make sure that the hook of the jack
handle driver is located squarely in the cap notch
before attempting to pull off.

You must use the flat end of the lug wrench to pull off the
wheel skins. Locate the hub cap pull notches (2 notches on
each cap). Insert the flat tip completely and using a back
and forth motion, loosen the wheel skin. Repeat this
procedure around the tire until the skin pops off.

Replace the wheel skins first using a rubber mallet. When
replacing the hub caps, tilt the cap retainer over the lug nut
bolt circle and strike the high side down with a rubber
mallet. Be sure that the hub caps and wheel skins are firmly
seated around the wheel.

Dual Rear Wheels

Slots in the wheels will assist in properly orienting the
inner and outer wheels. Align these slots when assembling
the wheels for best access to the tire valve on the inner

wheel. The tires of both dual wheels must be completely off
the ground when tightening to insure wheel centering and
maximum wheel clamping.

Dual wheel models require a special heavy-duty lug nut
tightening adapter (included with the vehicle) to correctly
tighten the lug nuts. Also, when it is necessary to remove
and install dual rear wheels, use a proper vehicle lifting
device.

NOTE:

When installing a spare tire (if equipped) as part of

a dual rear wheel end combination, the tire diameter of the
two individual tires must be compared. If there is a
significant difference, the larger tire should be installed in
a front location. The correct direction of rotation for dual
tire installations must also be observed.

It is recommended that wheel stud nuts be kept torqued to
specifications at all times. Torque wheel stud nuts to
specifications at each lubrication interval.

Wheel Nuts

All wheel nuts should be tightened occasionally to elimi-
nate the possibility of wheel studs being sheared or the bolt
holes in the wheels becoming elongated. This is especially
important during the first few hundred miles/kilometers
of operation to allow the wheel nuts to become properly

6

WHAT TO DO IN EMERGENCIES

439

«
...
439
440
441
442
443
...
»

Содержание Chassis Cab 2017































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Chassis Cab 2017

Бренд: Happy Orange Страницы: 2

Бренд: Ford Страницы: 2

Wallbox eM4 Single

Бренд: ABL Страницы: 68

Бренд: Conrad Страницы: 26

2003 Thunderbird

Бренд: Ford Страницы: 200

Бренд: Vintage Air Страницы: 28

Бренд: Chevrolet Страницы: 376

Бренд: Mazda Страницы: 15

Бренд: Webasto Страницы: 34

Бренд: Draw tite Страницы: 4

Бренд: EFILive Страницы: 25

FlashLogic FLC-FORS-FO1B-FLRSFO1-EN

Бренд: ADS Страницы: 25

Бренд: TomTom Страницы: 22

Бренд: Summit Racing Страницы: 11

Бренд: Fiat Страницы: 220

Giulia 952 2017

Бренд: Alfa Romeo Страницы: 324

Бренд: Rhino-Rack Страницы: 4

2012 Patriot Series

Бренд: Jeep Страницы: 505

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды