background image

RLCP05 Range Rover - Rhino 

Heavy Duty 3 Bar System

.

Important:

 

Please refer to your fitting instruction to ensure roof racks are installed in the correct locations.

Check contents of the kit before commencing fitment and report any discrepancies.

Place these instructions in the vehicle’s glove box after installation is complete.

Important Information

Maximum carrying capacity: 100kg (220lbs) evenly distributed over the cross bars.  Please refer to your vehicle

manufacturers handbook for maximum roof loading. Always use lower of the two figures.

Recommendations:

It is essential that all bolt connections be checked after driving a short distance when you first install your cross bars.  Bolt connec

-

tions should be checked again at regular intervals (probably once a week is enough, depending on road conditions, usage, loads 

and distances travelled).  You should also check the cross bars each time they are refitted. Make sure to fasten your load securely.  

Please ensure that all loads are evenly distributed and that the centre of gravity is kept as low as possible.  

Use only non-stretch fastening ropes or straps.
Caution:

 The handling characteristics of the vehicle changes when you transport a load on the roof.  For safety reasons we

recommend you exercise extreme care when transporting wind-resistant loads. Special consideration must be taken into account 

when cornering and braking.

Please remove cross bars when putting vehicle through an automatic car wash.
Load Ratings:

Maximum permissible load is 100kg (220lbs) for two cross bars including the weight of the cross bars, 7kg (15lbs). When cross 

bars are to be used in off-road conditions, please build a safety factor of 1.5 into this load limit for off-road use, two cross bars = 

66kg (145lbs)

.  Although the cross bars are tested and approved to AS1235-2000, Off road conditions can be much more rigor

-

ous. However, increasing the number of cross bars does not increase the vehicles maximum permissible roof loading.

Wash vehicle roof prior to installing roof 

racks.

NOTE: Please read through instructions before fitting the racks to your vehicle.

Содержание RLCP05

Страница 1: ...curely Please ensure that all loads are evenly distributed and that the centre of gravity is kept as low as possible Use only non stretch fastening ropes or straps Caution The handling characteristics of the vehicle changes when you transport a load on the roof For safety reasons we recommend you exercise extreme care when transporting wind resistant loads Special consideration must be taken into ...

Страница 2: ...1 Cross Bar 1375mm 3 A019 2 Rubber Buffer Strip 3 R001 3a M6 x 32mm Security Screw 2 B064 3b M6 x 45mm Security Screw 4 B091 4 End Cap 6 M002 5 M6 Spring Washer 6 W004 6 M6 Flat Washer 6 W003 7 M10 Channel Nut 6 N024 8 RLCP Leg 6 M123 9 M10 Flat Washer 6 W022 10a Mounting Pads Centre 2 M166 10b Mounting Pads Front Left Rear Right 2 M167 10c Mounting Pads Front Right Rear Left 2 M168 11 M10 Shake p...

Страница 3: ...0 Channel Nut M10 flat washer M10 shake proof washer M10 x 20mm bolt M6 x 32mm screw M6 spring washer M6 flat washer M6 x 45mm screw M6 spring washer M6 flat washer FRONT Left Right CENTRE Left Right REAR Left Right 3 Fit pads a Top of pads are marked according to their position on the roof b Orientate the pads correctly c Have the plastic roof flap up and position the pad into the recess FRONT TO...

Страница 4: ...so it locates across the inside of the cross bar Finger tighten only at this stage Channel nut must sit across the bar before tightening 6 Measure cross bar over hang Adjust cross bar over hang to be equal both sides Using the Allen key supplied tighten the M6 leg screws to 4 5 Nm 35 44 lbf in Tighten M10 cross bar bolts to 17 19 Nm 150 168 lbf in Do not over tighten EQUAL OVER HANG ...

Отзывы: