Rae ToxiRAE Pro Скачать руководство пользователя

Страница: 12 / 68

ToxiRAE Pro User’s Guide

5.1. Display Overview

The LCD display provides visual feedback that includes the sensor types, readings, time,
battery condition, and other functions.

5.2. Status Indicator Icons

Along the top of most screens are status indicators that tell you whether a function is
operating and/or its strength or level.

Icon

Function

Wireless status: the radio is on

Wireless status: the radio is off

The instrument is not equipped with a radio (no icon)

Wireless strength (0 to 5 bars), only when radio is turned on

Datalogging status (shown when datalogging is on, blank when off)

Battery status (three segments show battery charge level)

Man Down alarm enabled

Sensor calibration due

Bump test due

All sensors tested and calibrated tick mark (all sensors have been bump tested
and calibrated; no sensor is overdue for a bump test or calibration according to
the intervals configured on the instrument

Calibration and bump
test up to date

Sensor name and “Alarm” are
displayed alternately when in alarm

Wireless on/off status

Wireless signal strength

Unit of measure

Soft keys
(functions change by activity)

Alarm type
(when in alarm)

Bump test due

Sensor
calibration due

Reading

Man Down alarm on

Datalog on

Battery status

Содержание ToxiRAE Pro




































































Результаты поиска

Содержание ToxiRAE Pro

Отзывы:

Похожие инструкции для ToxiRAE Pro

Бренды по названию

Популярные бренды

Rae ToxiRAE Pro, Руководство пользователя

Результаты поиска

Содержание ToxiRAE Pro

Отзывы:

Похожие инструкции для ToxiRAE Pro

Бренды по названию

Популярные бренды