Radian RI-10W Скачать руководство пользователя страница 11

Страница: 11 / 53

RADIANQBIO INSTRUMENT www.radian21.com

④

SIG+

: Sensor Ouput Connection Terminal

⑤

SIG-

: Sensor Output Signal

–

Connection Terminal

⑥

GND

: SHIELD connection terminal of sensor

⑦

: Ground Terminal (as an independent ground connection.)

⑧

INC

: External Input Common Terminal

⑨

IN1

: External HOLD Input Terminal

⑩

IN2

: External ZERO Input Terminal

⑪

RYC

: RELAY Common Terminal

⑫

RY1

: RELAY1(Lower Limit) Output Terminal

⑬

RY2

: RELAY2 (Normal) Output Terminal (OK )

⑭

RY3

: RELAY3 (Upper Limit) Output Terminal

※

OPTION

⑮

GND, TXD, RXD : RS232C SERIAL INTERFACE Terminal

(RS485 : TXD -> TX+, RXD -> TX-)

○

GND, OUT

: Analog out Terminal (DC ±10V or DC 4~20mA)

◀Attention▶

1. When wiring, please pull out the power plug. (Main power supply)

2. Please use the thick calbe for ground terminal (

) so that you can avoid any trouble

due to the impulse voltage or surge. If possible, please keep it as an independent

ground.

(This must be used in the area with heavy noise. If the ground is made with other

device, it will be affected by noise.)

3. Please check the function of the terminal before you do the wiring so that you can

prevent any malfunction in advance.

4. Manufacture will be relieved of its responsibility for any damge or injury due to the

disassembly and alteration made without any agreement. Also, no A/S will be made.

Содержание RI-10W






















































Результаты поиска

Содержание RI-10W

Отзывы:

Похожие инструкции для RI-10W

Бренды по названию

Популярные бренды

Radian RI-10W, Руководство пользователя

Результаты поиска

Содержание RI-10W

Отзывы:

Похожие инструкции для RI-10W

Бренды по названию

Популярные бренды