Radian RI-10W Скачать руководство пользователя страница 36 | Manualshive

Страница: 36 / 53

Radian RI-10W Скачать руководство пользователя страница 36

RADIANQBIO INSTRUMENT www.radian21.com

35

2)

Compensation functions and notice

If the actual load (load, displacement, pressure) is applied to the sensor and there is a

difference between the value displayed in the indicator and the actual load value, the display

value of the indicator can be changed to the actual load value. Up to 9 points can be stored. As

the calibration interval is differentiated, the linearity of the sensor can be increased. In the actual

load calibration mode, calibration is possible at the forward (+) output of the sensor and

calibration is not possible at the reverse (-) output of the sensor.

If an incorrect value is entered during setup, re-calibration with 8-4 Digital calibration,

delete all data of the values changed to the actual load calibration setting.

Then re-run the actual load calibration setting.

< After Compensation >

①

Sensor output(display data)

②

Real load data

③

Values stored with calibration
settings

< Before Compensation >

①

Sensor output(display data)

②

Real load data

capacity

kg

output

mV/V

①

②

③

capacity

kg

output

mV/V

①

②

③

«
...
34
35
36
37
38
...
»

Содержание RI-10W






















































Отзывы:

Нет отзывов