Radian RI-10W Скачать руководство пользователя страница 3

Страница: 3 / 53

RADIANQBIO INSTRUMENT www.radian21.com

1. Features

We thank you for using our product. Please refer to this manual or contact our office if

you find any problems during using our product.

This product is an indicator that emplifies the micro voltage signals from each sensor

and display in digital. It is mainly used to measure physical quantities of the items using

strain guage such as loadcell, pressure sensor, displacement sensor and torque sensor.

This product has the following special features.

1-1. Calibration method

Calibration by actual load (standard weight) and calibration by rated output of sensor.

1-2. Hold and Peak Hold

You can choose peak hold and sample hold as per your need.

1-3. Comparison Output

You can do set-up the maxium and lower limit value by the keys on the front panel

and print with contact point signal of the rear panel.

1-4. Data Back-up

All the set-up values will be memorized on the flash memory so the inputted data can

be saved and no need to do the re-setting even in case of the interruption of the

electric power or power disconnection.

1-5. Watch dog

This function is for automatic reset in case the system is stopped due to the external factors such as noise.

1-6. Option

• OP-01 : Parallel BCD output

• OP-02 : RS232C Interface (basic installation)

• OP-03 : RS485 Interface

• OP-10 : Power DC24V 0.3A

Additional optional RS232C, RS485, or BCD outputs are available, and our standard

protocol and Modbus RTU protocol can be selected from Function settings.

1-7. Power

AC 90 ~ 240V 50/60Hz 8VA (Option : DC24V 0.3A)

Model RI-148A,B Power: DC24V 0.2A

Содержание RI-10W






















































Результаты поиска

Содержание RI-10W

Отзывы:

Похожие инструкции для RI-10W

Бренды по названию

Популярные бренды

Radian RI-10W, Руководство пользователя

Результаты поиска

Содержание RI-10W

Отзывы:

Похожие инструкции для RI-10W

Бренды по названию

Популярные бренды