Quatech Serial Device Server страница 66 Скачать руководство пользователя

Страница: 66 / 98

Configuring the SDS using a Web interface

Quatech SDS User’s Manual

Step

Procedure

Description

Balanced

mode

offers

excellent

performance

for

most

applications.

Low

Latency

mode

heavily

favors

responsiveness

over

throughput.

Step 3c

Set the Heart Beat Time to a value from 1

to 65534 seconds. Default is 45 seconds.

Note: Use a value of 0 to disable the heartbeat
timer.

Heartbeat messages help detect when a

connection has been lost between the PC

driver and the SDS.
If you need quick notification that the

connection has been lost, set this timer to
a shorter value.
If you are more concerned about network

traffic, set this timer to a longer value.

Step 3d

Click on the desired Tunnel End Type

selector. If Slave, skip to Step 4. If
Master, continue with Steps 3e–3k.

Note: Steps 3e–3k are only available if the
Tunnel End Type is set to Master. If it is set to
Slave, they are grayed out.

This selection determines which end of

the serial tunnel connection is the
Master and which is the Slave. At this

point, your Slave ports are completely
configured. Master ports must have the

following parameters set.

Step 3e

Set the Baud Rate.

The SDS and the serial device(s) to

which it is attached must use the same
serial connection speed.

Step 3f

Set the Parity.

Parity can be odd, even, or none.

Step 3g

Set the Data Bits.

Data Bits can be 7 or 8.

Step 3h

Set the Stop Bits.

Stop Bits can be 1 or 2.

Step 3i

Set the Flow Control.

Flow control determines the handshake

method used between the SDS and the
serial device(s) to stop the serial

input/output process

Step 3j

Set the IP Address of the Slave SDS.

This selection sets the IP address to be

used in Serial Tunneling mode.

Step 3k

Set the Serial/TCP Port number on the
Slave SDS.

This selection sets the serial port for
Serial Tunneling mode. For a single-

port Slave SDS, enter “1”; for a multi-

port Slave SDS, enter the port number
according to the label next to the

connector you plan to use.

Steps 4a through 4d apply only to RS-232/422/485 (MEI) units

Step 4a

(MEI only)

Configure the serial port interface.

Click on the desired interface selector.

This series of steps only applies to MEI

units, such as the SSE-400.
If you select RS232, the RS422/485
selections will be grayed out. Continue

with

□

Step 5

Page 60

940-0183-153

July 2005

Содержание Serial Device Server



































































































Результаты поиска

Содержание Serial Device Server

Отзывы:

Похожие инструкции для Serial Device Server

Бренды по названию

Популярные бренды

Quatech Serial Device Server, Руководство пользователя

Результаты поиска

Содержание Serial Device Server

Отзывы:

Похожие инструкции для Serial Device Server

Бренды по названию

Популярные бренды