Quatech Serial Device Server страница 69 Скачать руководство пользователя

Страница: 69 / 98

Quatech SDS User’s Manual

Configuring the SDS using a Web interface

Step

Procedure

Description

Force X2 mode

Force X4 mode

Force X8 mode

Note: Forcing a change in the data rate may
cause communication problems with some

serial devices. If this is the case, change the
setting back to Auto (Recommended).

Step 3b

Click on the desired Performance

Selector.

Choose balanced mode except in those

cases where the serial device cannot
tolerate the slight delays inherent in

normal TCP/IP operation.

Balanced

mode

offers

excellent

performance

for

most

applications.

Low

Latency

mode

heavily

favors

responsiveness

over

throughput.

Step 3c

Set the Heart Beat Time to a value from 1
to 65534 seconds. Default is 45 seconds.

Note: Use a value of 0 to disable the heartbeat
timer.

Heartbeat messages help detect when a
connection has been lost between the PC

driver and the SDS.
If you need quick notification that the
connection has been lost, set this timer to

a shorter value.
If you are more concerned about network
traffic, set this timer to a longer value.

Step 3d

Set the Baud Rate.

The SDS and the serial device(s) to

which it is attached must use the same

serial connection speed.

Step 3e

Set the Parity.

Parity can be odd, even, or none.

Step 3f

Set the Data Bits.

Data Bits can be 7 or 8.

Step 3g

Set the Stop Bits.

Stop Bits can be 1 or 2.

Step 3h

Set the Flow Control.

Flow control determines the handshake

method used between the SDS and the

serial device(s) to stop the serial
input/output process.

Steps 4a through 4d apply only to RS-232/422/485 (MEI) units

Step 4a

(MEI only)

Configure the serial port interface.

Click on the desired interface selector.

This series of steps only applies to MEI
units, such as the SSE-400.
If you select RS232, the RS422/485

selections will be grayed out. Continue
with

□

Step 5

Step 4b

(MEI only)

Click on the desired duplex mode selector.

Select

Full Duplex

to always enable

transmit and receive drivers.
Select

Half Rx

to only enable the

transmit drivers when the SDS is

transmitting; receivers always enabled.
Select

Half Rx Tog

to disable receivers

and enable the transmit drivers only
when the SDS is transmitting.

July 2005

940-0183-153

Page 63

Содержание Serial Device Server



































































































Результаты поиска

Содержание Serial Device Server

Отзывы:

Похожие инструкции для Serial Device Server

Бренды по названию

Популярные бренды

Quatech Serial Device Server, Руководство пользователя

Результаты поиска

Содержание Serial Device Server

Отзывы:

Похожие инструкции для Serial Device Server

Бренды по названию

Популярные бренды