Quatech Serial Device Server Скачать руководство пользователя

Страница: 23 / 98

Quatech SDS User’s Manual

Installing the device drivers

Figure 7 - Welcome screen

Step

Procedure

Description

Step 5

Click the Next button to continue.

The Prepare to Install screen displays.

Continue with

□

Step 6.

Figure 8 - Prepare to Install screen

Step

Procedure

Description

Step 6

Connect the Ethernet port on your SDS to

one of the following:

Desired installation location,

Hub on your local subnet, or

Network Interface Connection (NIC)

on your computer using an Ethernet
crossover patch cable.

If you cannot immediately attach the SDS

to the target installation site, temporarily

attach it to the local hub or your computer’s
NIC for configuration purposes.

Notes: Use a CAT5 or better Ethernet cable
to attach the SDS to your network.
If your SDS is pre-configured for your
network, attach it now to the appropriate
subnet location.

Continue with

□

Step 7.

Note: Press the Help key for
additional information as you

go through the installation
procedure.

Figure 9 illustrates the Prepare

to Install prompt. Be sure to

read this screen carefully

before proceeding.

Figure 8 illustrates the Quatech

Install Wizard’s Welcome

screen.

July 2005

940-0183-153

Page 17

Содержание Serial Device Server



































































































Результаты поиска

Содержание Serial Device Server

Отзывы:

Похожие инструкции для Serial Device Server

Бренды по названию

Популярные бренды

Quatech Serial Device Server, Руководство пользователя

Результаты поиска

Содержание Serial Device Server

Отзывы:

Похожие инструкции для Serial Device Server

Бренды по названию

Популярные бренды