Quatech Serial Device Server Скачать руководство пользователя

Страница: 65 / 98

Quatech SDS User’s Manual

Configuring the SDS using a Web interface

Figure 53 - Serial Port Setup screen for Tunneling mode

Note: Click on a link
to see a pop-up help
screen for that item.

Step

Procedure

Description

Step 1

Select the serial port you want to
configure.

Click on a port number to select that
port. The selections on the screen are

automatically populated with any

existing parameters for the selected port.

Step 2

Click on the Tunneling Operating Mode
selector.

Tunneling allows two SDS devices to
create a virtual connection between their

serial ports.
You will find directions for configuring

ports in Normal mode in the previous

section. Directions for Raw TCP, Auto
TCP and Raw UDP modes are in the

following sections.

Step 3a

Configure the Operating mode.
Click on the desired data Rate Multiplier.
Your choices are:

Auto (Recommended)

Force X2 mode

Force X4 mode

Force X8 mode

The auto setting has no effect on the

baud rate you set. However, if you select
X2, X4, or X8, the baud rate of the serial

port will be the baud rate that you set

multiplied by 2, 4, or 8, respectively.

Note: Forcing a change in the data rate may
cause communication problems with some

serial devices. If this is the case, change the
setting back to Auto (Recommended).

Step 3b

Click on the desired Performance

Selector.

Choose balanced mode except in those

cases where the serial device cannot

tolerate the slight delays inherent in
normal TCP/IP operation.

July 2005

940-0183-153

Page 59

Содержание Serial Device Server



































































































Результаты поиска

Содержание Serial Device Server

Отзывы:

Похожие инструкции для Serial Device Server

Бренды по названию

Популярные бренды

Quatech Serial Device Server, Руководство пользователя

Результаты поиска

Содержание Serial Device Server

Отзывы:

Похожие инструкции для Serial Device Server

Бренды по названию

Популярные бренды