background image

20

 

 

 
 

E07

 

H2O Level

-

Bad Tri

-

Probe

 

 

 

Tri

-

Probe application only.  Check connections to the Tri

-

Probe Assembly.

 

 
 

 

 

Terminal J2

-

4 = Short Probe (Gray Wire)

 

 

 

 

Terminal J2

-

5 = Medium Probe (Violet Wire)

 

 

 

 

Terminal J2

-

6 = Long Probe (Blue Wire)

 

 

 

 

Terminal J2

-

7 = Tank Ground (Green Wire)

 

 

 

 

 

 

Note: To check operation, temporarily install three (3) jumpers across

 

 

 

terminals J2

-

4, J2

-

5, J2

-

6, and J2

-

7.  This should clear Error Code E07.  

 

 

 

WARNING

:  This procedure defeats the low water safety circuit.  Ensure there is 

 

 

 

an adequate amount of water in the humidifier tank before proceeding.  If this 

 

 

 

procedure clears the error code, check the Tri

-

Probe Assembly and its associated 

 

 

 

wiring.  Verify tank grounding to terminal J2

-

7. Refer to specifications page for 

 

 

 

wiring limitations.

 

 

E07

 

H2O Level

-

Refill Fault

 

 

 

Tri

-

Probe application only.  Check connections to the Tri

-

Probe Assembly.

 

 
 

 

 

Terminal J2

-

4 = Short Probe (Gray Wire)

 

 

 

 

Terminal J2

-

5 = Medium Probe (Violet Wire)

 

 

 

 

Terminal J2

-

6 = Long Probe (Blue Wire)

 

 

 

 

Terminal J2

-

7 = Tank Ground (Green Wire)

 

 
 

 

Occurs when fill valve has been on continuously for 1 hour

 

 

 

 

 

 

 

Check water source supply.  Verify that water is actually filling the tank to 

 

 

 

the TOP water level probe.

 

 

 

 

 

 

Note:  To reset this alarm message, momentarily switch the power off and 

 

 

 

on to the INTAC

®

 Controller.

 

 

E07

 

H2O Level

-

Drain Fault

 

 

 

Unit did not drain properly during drain cycle.  Check for sediment blockage

 

 

 

in drain valve and drain line.  The drain duration may not be set long enough.  The 

 

 

water level must read “Low” during the auto drain or this fault will occur.

 

 

E08

 

Module I/O Error 

-

 DLCM #1

 

 

 

It is likely the controller has been damaged and needs replacement

 

 

E08

 

Module I/O Error 

-

 DLCM #2

 

 

 

It is likely the controller has been damaged and needs replacement

 

 

 

E08

 

Module I/O Error 

-

 WLCM

 

 

 

It is likely the controller has been damaged and needs replacement

 

 

A01

 

RH Alarm

-

Low RH

 

 

 

The actual RH is below the limit set in Configuration Menu 103

 

 

A01

 

RH Alarm

-

High RH

 

 

 

The actual RH is above the limit set in Configuration Menu 104

 

Содержание INTAC

































Отзывы: