PT AMC131 Скачать руководство пользователя | Manualshive

Страница: 67 / 108

background image

Serial Interface Subsystem

67

Payload Communication Timeout

Some of the SIPL commands are subject to payload communication timeouts. If the payload
does not respond with a correct reply within a definite period of time, the MMC assumes that a
payload communication timeout occurred and acts accordingly. The SIPL timeout value also
limits the period of time given to the payload to prepare for a payload reset.

“Get Payload Communication Timeout Command,” on page 67

“Set Payload Communication Timeout Command,” on page 67

Get Payload Communication Timeout Command

The MMC supports reading of the payload communication timeout using the

Get Payload

Communication Timeout

command. This command has the following synopsis:

[B8 xx 09 0A 40 00]

The MMC responds to the

Get Payload Communication Timeout

command with the

following reply:

[BC xx 09 00 0A 40 00

<payload timeout>

]

The

<payload timeout>

parameter is the payload communication timeout measured in

hundreds of milliseconds. Thus, the payload communication timeout may vary from 0.1 to 25.5
seconds. The default value of the payload communication timeout is specified by the
CFG_APP_SIPL_PAYLOAD_TIMEOUT Configuration Parameter.

Set Payload Communication Timeout Command

To change the payload communication timeout, the

Set Payload Communication Timeout

command is used:

[B8 xx 0A 0A 40 00

<payload timeout>

]

Graceful Payload Reset

The MMC supports the Graceful Reboot option of the

FRU Control

command. On receiving

such a command, the MMC sets the Graceful Reboot Request bit of the MMC status, sends a
status update notification to the payload, and waits for the

Graceful Reset

command from the

payload. If the MMC receives such a command before the payload communication timeout
time, it sends the 0x00 completion code (Success) to the carrier controller. Otherwise, the 0xC3
completion code (Timeout) is sent.

The

Graceful Reset

command has the following synopsis:

[B8 xx 11 0A 40 00]

Note that the MMC does not reset the payload on receiving the

Graceful Reset

command or

timeout. If the MMC participation is necessary, the payload must request the MMC to perform a
payload reset.

The

Graceful Reset

command is also used to notify the MMC about the completion of the

payload shutdown sequence (refer to

“Payload Shutdown Timeout,” on

«
...
65
66
67
68
69
...
»

Содержание AMC131













































































































Отзывы:

Нет отзывов

Похожие инструкции для AMC131

Бренд: RTimes Страницы: 23

Бренд: BabyBjorn Страницы: 6

Бренд: Vaude Страницы: 129

Бренд: TBG Страницы: 27

Бренд: Advantech Страницы: 2

Бренд: iWave Страницы: 164

Бренд: Liinalapsi Oy Страницы: 9

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды