PT AMC131 Скачать руководство пользователя | Manualshive

Страница: 30 / 108

background image

Chapter 2: Introduction

30

LED Indicators

The AMC131 provides eight LED indicators (see

Figure 2-1, “AMC131 Front Panel,” on page

describes the AMC131 LEDs and their functions.

*The OOS and IS LEDs are used to indicate an “out of service” condition or an “in service” status, per the PICMG Ad-
vanced Mezzanine Card AMC.0 Specification R2.0. Although these LEDs are managed by the MMC, a carrier manager
or shelf manager can override the MMC's local LED settings.

The OOS LED is activated to indicate that the payload is known to be out of service (payload power is off, held in reset,
or faulted in a way that precludes operation). Otherwise the OOS LED is off. The health of the board cannot be inferred
solely from the state of this LED. The default local color of the OOS LED is determined by FRU data and is configurable
as either red or amber. Contact PT Customer Support for information about configuring this color.

The IS LED is activated when the OOS LED is turned off. It is never turned on when the OOS LED is on. The IS LED
is green when all sensors are within the critical thresholds or amber when one or more sensors have exceeded a critical
threshold.

Table 2-5:

AMC131 LED Architecture

LED Name

Color

Description

AMC LED 1 (OOS)*

Red

Out Of Service (geographic Option 1)

Amber

Out Of Service (geographic Option 2)

AMC LED 2 (IS)*

Green

In Service (MMC Defined)

USB

Off

No USB Device Present

Green

USB Device Present

Ethernet 1 Link/Activity

Off

No Link

Green

Link Established but No Activity

Blinking green

Link Established and Tx or Rx Activity

CPU1 Status

Off

LED Circuit Failure

Amber

Power OK, CPU1 Can Boot

Green

CPU1 In Service

Red

CPU1 Fault

Ethernet 2 Link/Activity

Off

No Link

Green

Link Established but No Activity

Blinking green

Link Established and Tx or Rx Activity

CPU2 Status

Off

LED Circuit Failure

Amber

Power OK, CPU2 Can Boot

Green

CPU2 In Service

Red

CPU2 Fault

Hot Swap

Blue

It is Safe to Extract the Module

Blinking Blue

In Transition; Not Safe to Extract the Module

Off

It is Not Safe to Extract the Module.

«
...
28
29
30
31
32
...
»

Содержание AMC131













































































































Отзывы:

Нет отзывов

Похожие инструкции для AMC131

MicroMod DEV-18575

Бренд: sparkfun Страницы: 33

Бренд: We Made Me Страницы: 30

Бренд: Fräulein Hübsch Страницы: 20

Бренд: Dorel Страницы: 84

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды