PT AMC131 Скачать руководство пользователя страница 105 | Manualshive

Страница: 105 / 108

background image

Industry Canada Class A Notice

105

Industry Canada Class A Notice

This Class A digital apparatus complies with Industry Canada’s Equipment Standard for Digital
Equipment (ICES-003).

Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada.

Product Safety Information

Safety Precautions

Review the following precautions to avoid injury and prevent damage to this product, or any
products to which it is connected. To avoid potential hazards, use the product only as specified.

Read all safety information provided in the component product user manuals and understand
the precautions associated with safety symbols, written warnings, and cautions before
accessing parts or locations within the unit. Save this document for future reference.

Caution:

To Avoid Burns: If there is a heat sink on this module, it can get very hot during normal
operation. To avoid burns, take extra care when removing the module from the chassis soon
after shutdown. Wait a few minutes to allow the heat sink to cool down.

Caution:

Handling the Module: It is important to hold the module only by the front panel or PCB
edges. Avoid touching any components unless necessary to service the product. Do not
handle the heat sink, as this can adversely affect the thermal connection between the heat
sink and the processor, and cause the processor to overheat under normal operating
conditions.

Caution:

To Avoid Electric Overload: To avoid electrical hazards (heat, shock and/or fire hazard),
do not make connections to terminals outside the range specified for that terminal. Refer to
the product user manual for correct connections.

Caution:

To Avoid the Risk of Electric Shock: When supplying power to the system, always make
connections to a grounded main. Always use a power cable with a grounded plug (third
grounding pin). Do not operate in wet, damp, or condensing conditions.

«
...
103
104
105
106
107
...
»

Содержание AMC131













































































































Отзывы:

Нет отзывов

Похожие инструкции для AMC131

BaByBjörn Baby Carrier Origina

Бренд: BabyBjorn Страницы: 5

Бренд: Baby K’tan Страницы: 28

Бренд: Lionelo Страницы: 12

Бренд: Tula Страницы: 36

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды