PT AMC131 Скачать руководство пользователя | Manualshive

Страница: 41 / 108

background image

Physical Installation

41

Physical Installation

Before installing the AMC131, make sure the module is correctly configured for your
application.

Installing the AMC131

The following instructions assume that chassis power is on and that the system supports hot-
swap insertion. If the system does not support hot swap, power must be turned off prior to
installation.

1. Unlock the ejector handle by gently pulling it away from the front panel.

2. Slide the AMC131 into an available slot in the system, aligning the board with the guides near the top

of the slot. The module audibly snaps into place when properly inserted.

3. Press the handle toward the front panel to lock the module in the chassis. When the module card

edge connector makes proper contact with the backplane connector, the blue hot swap LED turns ON
and the hardware connection process begins. When the module is operational, the blue hot swap
LED turns OFF.

4. Connect any cables from peripheral devices.

Removing the AMC131

To remove the module:

1. Unlock the module by pulling the handle away from the front panel. The blue hot swap LED blinks to

indicate that the handle is open and the module is waiting to be deactivated. It is not yet safe to
extract the module in this state. Wait until the blue LED stops blinking and remains illuminated to
indicate that the board is ready for extraction.

2. When the blue LED stops blinking and remains illuminated, the module is quiesced and module

payload power is disabled. It is now safe to extract the module. Gently pull on the handle to remove
the module from the system.

«
...
39
40
41
42
43
...
»

Содержание AMC131













































































































Отзывы:

Нет отзывов

Похожие инструкции для AMC131

MOSES BASKET Series

Бренд: Badger Basket Страницы: 3

Бренд: Bebecar Страницы: 40

Бренд: sparkfun Страницы: 81

Бренд: BabyBjorn Страницы: 65

Бренд: BabyBjorn Страницы: 184

Бренд: Inglesina Страницы: 36

Бренд: Inglesina Страницы: 48

Бренд: Graco Страницы: 8

Бренд: Graco Страницы: 11

Бренд: Graco Страницы: 22

Бренд: Graco Страницы: 37

Quattro Tour Deluxe

Бренд: Graco Страницы: 74

Бренд: Graco Страницы: 92

Бренд: Graco Страницы: 128

Бренд: Graco Страницы: 78

8465GIS3 - SnugRide Infant Car Seat

Бренд: Graco Страницы: 90

Бренд: Graco Страницы: 92

Бренд: Graco Страницы: 120

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды