PRÜFTECHNIK EDDYTHERM Скачать руководство пользователя страница 29

Страница: 29 / 32

EDDYTHERM operating manual

Crossbars

EDDYTHERM is delivered with crossbars in a variety of sizes.

The crossbars consist of thin, laminated sheets. Do not use them as a hammer or lever.

Always mount the crossbars on EDDYTHERM so that their laminates are oriented vertically (with the unpainted side

facing down); see the ﬁgure below.

Overview

Scope of delivery

and optional accessories

EDDYTHERM Ix

EDDYTHERM 1-6

EDDYTHERM 4x

Crossbars for inside ø

Order no.

> ø 15 mm

ETH 7650

❍

> ø 20 mm

ETH 7651

●

❍

> ø 30 mm

ETH 7652

❍

●

> ø 43 mm

ETH 7653

●

❍

> ø 64 mm

ETH 7654

❍

●

> ø 79 mm

ETH 7655

●

❍

> ø 86 mm

ETH 7656

●

> ø 43 mm

ETH 7648

❍

> ø 58 mm

ETH 7647

❍

Container for crossbars

ETH 7905

❍

Swivel crossbars for inside ø

> ø 108 mm

ETH 7640

●

> ø 79 mm

ETH 7641

❍

Demagnetization bar

ETH 7670

❍

Temp. probe, magnetic holder ETH 7305

●

Clip-on type temperature probe ETH 7303

❍

Optional

●

Included

The crossbars

ust

ounted on the

EDDYTHERM with the

inates in a vertical

position.

Содержание EDDYTHERM

































Результаты поиска

Содержание EDDYTHERM

Отзывы:

Похожие инструкции для EDDYTHERM

Бренды по названию

Популярные бренды

PRÜFTECHNIK EDDYTHERM, Руководство по эксплуатации

Результаты поиска

Содержание EDDYTHERM

Отзывы:

Похожие инструкции для EDDYTHERM

Бренды по названию

Популярные бренды