PRÜFTECHNIK EDDYSENSOR Скачать руководство пользователя

Страница: 9 / 53

EDDYSENSOR Operating Manual

The EDDYSENSOR is a simple eddycurrent detection

device which senses the presence of a defect to

activate subsequent activities, e.g. shutting off the

cooling water in a welding line with annealing. The

minimum configuration consists of two units in a table-

top housing. A third unit is optional.

The minimum configuration is made up of the Front

End Unit in the left-hand position and the Power Unit in

the right-hand position. For safety reasons, the back

module of the Power Unit is supplied immovably as-

sembled in the table-top housing, LAB 1004. The op-

tional unit is the Delay Unit in the middle position. The

modules and their positions are shown in the diagram

above.

EDDYSENSOR System Diagram

Output signal
to peripherals

Input signal from test coil

Front End Unit

Front module

FM103xF

Optional

Power Unit

Delay Unit

Back module

FI103xBAfff

Front module

DM1050F

Back module

DI1050BA

Front module

PM1040F

Back module

PI1040BA

Содержание EDDYSENSOR






















































Результаты поиска

Содержание EDDYSENSOR

Отзывы:

Похожие инструкции для EDDYSENSOR

Бренды по названию

Популярные бренды

PRÜFTECHNIK EDDYSENSOR, Руководство по эксплуатации

Результаты поиска

Содержание EDDYSENSOR

Отзывы:

Похожие инструкции для EDDYSENSOR

Бренды по названию

Популярные бренды