PRÜFTECHNIK EDDYSENSOR Скачать руководство пользователя

Страница: 37 / 53

EDDYSENSOR Operating Manual

Example:

WICU line with encoder

First, set up the filters for the testing speed of e.g. 80 m/min.

Using the recommended calculations:-

For the high pass filter

80/4 = 20

From the table or the graph for the high pass filter using an encircling coil,

the setting of the switches HPH/HPL is 17 (HPH=1, HPL=7).

For the low pass filter

80 x 2 = 160

From the table or the graph for the low pass filter using an encircling coil,

the setting of the switches LPH/LPL is 12 (LPH=1, LPL=2).

Turn the filter switches to the correct settings using a screwdriver.

Front End settings

High pass filter

Low pass filter

Encoder

Undelayed

Delayed 1

Delayed 2

DM 1.050F

Off

Power

EDDYSENSOR

Gain [dB]

Gain

FM 1.030F

Defect

Coil error

Overload

100

+5V

+15V

-15V

PM 1.040F

Encoder

In this example the undelayed signal is used to activate a warning device

and the delayed signal goes to a paint marker (10 m distance) which colour

marks the ends of the copper tubes for subsequent cutting. These pieces

are then cut out by a flying saw (at a distance of 22.5 m).

1030 filter settings

1031 filter settings

First, set up the filters for the testing speed of e.g. 80 m/min.

Using the recommended calculations:-

For the high pass filter

80/4 = 20

From the table or the graph for the high pass filter using an encircling coil,

the setting of the HP is 12.

For the low pass filter

80 x 2 = 160

From the table or the graph for the low pass filter using an encircling coil,

the setting of the switches LP is 11.

Set the filter switches to the correct settings as explained in the module

description.

Содержание EDDYSENSOR






















































Результаты поиска

Содержание EDDYSENSOR

Отзывы:

Похожие инструкции для EDDYSENSOR

Бренды по названию

Популярные бренды

PRÜFTECHNIK EDDYSENSOR, Руководство по эксплуатации

Результаты поиска

Содержание EDDYSENSOR

Отзывы:

Похожие инструкции для EDDYSENSOR

Бренды по названию

Популярные бренды