PRÜFTECHNIK EDDYSENSOR Скачать руководство пользователя

Страница: 43 / 53

EDDYSENSOR Operating Manual

Locating and changing fuses

Fuses

PCB of the back module

The fuses for the outputs of the delay unit are located on the back module

DI1050BA.

Delay Unit

In carrying out any work on the equipment, please observe the ESD

instructions given on the separate sheet at the beginning of this handbook.

To replace a fuse, switch off the power and then:

Remove the back module by loosening the four retaining screws.

Pull the module carefully out of the housing.

Remove the blown fuse(s).

Insert the new fuse(s).

Slide the back module into its slot in the housing and seat it firmly.

Tighten up the four retaining screws again.

Replacing the fuses

There are four fuse holders (F1 for OUT1, F2 for OUT2, F3 for OUT3, F4 is

not used) available. The first three must contain 630 mA fast fuses.

If the peripheral on a specific output does not function, check the corre-

sponding fuse.

The four fuse holders

There are four fuse holders (F1 for OUT1, F2 for OUT2, F3 for OUT3, F4 for

OUT4) available. They must contain 1.25 A slow fuses.

If the peripheral on a specific output does not function, check the corre-

sponding fuse.

The four fuse holders

Fuses
up to modification status d

(status appears on the con-
nector block of the PCB)

Fuses
from modification status e

(status appears on the con-
nector block of the PCB)

Front

Back

DI1050BA

Содержание EDDYSENSOR






















































Результаты поиска

Содержание EDDYSENSOR

Отзывы:

Похожие инструкции для EDDYSENSOR

Бренды по названию

Популярные бренды

PRÜFTECHNIK EDDYSENSOR, Руководство по эксплуатации

Результаты поиска

Содержание EDDYSENSOR

Отзывы:

Похожие инструкции для EDDYSENSOR

Бренды по названию

Популярные бренды