ProSoft Technology PLX51-HART-4I Скачать руководство пользователя страница 31

Страница: 31 / 127

PLX51-HART-4I / PLX51-HART-4O

♦

HART Input/Output

Setup

Multidrop Field Devices

User Manual

ProSoft Technology, Inc.

Page 31 of 127

The Advanced Mapping configuration tab consists of the following parameters:

Table 3.3 – Advanced Diagnostics parameters

Parameter

Description

Action

Diagnostics

When the

Diagnostics

option is selected, the user will be able to configure a

specific HART command that must be sent to the “main” device (usually at the

specified fixed address). The result will then be written to a configured Logix

tag thus allowing the user to extract device specific diagnostics from a field

device.

Multi-Drop

When the

Multidrop

option is selected the module will automatically extract

all the required information from the device at the specified address (see

below), allowing the user to have multiple HART devices on a single HART

channel.

Custom

When the

Custom

option is selected a custom HART message can be build

with data being read from and/or written to the protocol interface. Custom

messages are supported for EtherNet/IP and Modbus TCP. The user will

need to select the HART device short address.

This is the Multidrop Device Index for the specific HART device. There can be

a maximum of 7 devices (0-6) per channel and each Multidrop Device Index

will specify the location where the multidrop data is stored and can be

accessed by the various interface protocols (see the multidrop section for

more details).

Applicable only for

Multi-Drop

Action.

Address

This is the short node address of the HART device on the multidrop channel.

The addresses can be found by using the Scan function in the Device List tab

(see the Diagnostics and Multidrop sections for more details).

Important:

Connecting more than one device with the same short address will cause

communication errors and prevent both devices from being detected during a scan.

Applicable only for

Multi-Drop

Custom

Action.

Description

A user description for the device or diagnostic parameter.

Build

This button launches the HART Advanced Diagnostics Builder which is used

to create the HART message required to extract the needed parameter.
(See Advanced Diagnostic Builder below.)

Applicable only for EtherNet/IP interface protocol when using

Diagnostics

Action or EtherNet/IP and Modbus TCP when using

Custom

Action.

Data Type

For Action – Diagnostics

The Logix tag data type required to accept the parameter.

For Action – Multi-Drop

The data type will specify if the UDT to be used must be of the legacy

MVI56Legacy format or the new Multi-Drop format.

Important:

The user will need to ensure that the correct UDT is used for the Logix tag when

using either new or legacy format for Multi-Drop operation.

Applicable only for EtherNet/IP interface protocol.

Logix Tag

The Logix tag name mapped to receive the parameter.

Applicable only for EtherNet/IP interface protocol.

Browse

This button launches the Tag Browser for the configured Logix controller.

Applicable only for EtherNet/IP interface protocol.

3.5.1 Diagnostics

Содержание PLX51-HART-4I
































































































































Результаты поиска

Содержание PLX51-HART-4I

Отзывы:

ProSoft Technology PLX51-HART-4I, Руководство пользователя, Страница: 31 / 127

Результаты поиска

Содержание PLX51-HART-4I

Отзывы: