manualshive.com logo in svg

ProSoft Technology inRAx MVI56-CAS, Руководство пользователя

Поделиться
Скачать
ProSoft Technology inRAx MVI56-CAS Скачать руководство пользователя страница 52

MVI56-CAS 

♦

 ControlLogix Platform 

Reference 

Teledyne CA Slave Module  

 

Page 52 of 86  

ProSoft Technology, Inc. 

December 26, 2007 

 

Data contained in this database is paged through the input and output images by 
coordination of the ControlLogix ladder logic and the MVI56-CAS module's 
program. Up to 248 words of data can be transferred from the module to the 
processor at a time. Up to 247 words of data can be transferred from the 
processor to the module. Each image has a defined structure depending on the 
data content and the function of the data transfer as defined below. 

5.2.2  Normal Data Transfer 

Normal data transfer includes the paging of the user data found in the module's 
internal database in registers 0 to 4999 and the status data. These data are 
transferred through read (input image) and write (output image) blocks. Refer to 
the 

Module Set Up 

section for a description of the data objects used with the 

blocks and the ladder logic required. The structure and function of each block is 
discussed below. 

Read Block 

These blocks of data transfer information from the module to the ControlLogix 
processor. The structure of the input image used to transfer this data is shown in 
the following table: 

Offset Description 

Length 

0 Reserved 

1 

1 

Write Block ID 

1 

2 to 201 

Read Data 

200 

202 

Program Scan Counter 

1 

203 to 204 

Product Code 

2 

205 to 206 

Product Version 

2 

207 to 208 

Operating System 

2 

209 to 210 

Run Number 

2 

211 to 217 

Port 1 Error Status 

7 

218 to 224 

Port 2 Error Status 

7 

225 to 230 

Data Transfer Status 

6 

231 

Port 1 Current Error/Index 

1 

232 

Port 1 Last Error/Index 

1 

233 

Port 2 Current Error/Index 

1 

234 

Port 2 Last Error/Index 

1 

235 

Port 1 Status Scan 

1 

236 

Port 2 Status Scan 

1 

237 to 248 

Spare 

12 

249 

Read Block ID 

1 

Содержание inRAx MVI56-CAS























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды