manualshive.com logo in svg

ProSoft Technology inRAx MVI56-CAS, Руководство пользователя

Поделиться
Скачать
ProSoft Technology inRAx MVI56-CAS Скачать руководство пользователя страница 41

Diagnostics and Troubleshooting 

MVI56-CAS 

♦

 ControlLogix Platform 

 

Teledyne CA Slave Module 

 

ProSoft Technology, Inc. 

Page 41 of 86 

December 26, 2007 
 

The <R+> means that the module is transitioning the communications line to a 
transmit state. 

All characters shown in <> brackets are characters being sent out by the module. 

The <R-> shows when the module is done transmitting data, and is now ready to 
receive information back. 

And finally, all characters shown in the [ ] brackets is information being received 
from another device by the module. 

After taking a minute or two of traffic capture, you will now want to stop the "Data 
Analyzer". To do so, press the 'S' key, and you will then see the scrolling of the 
data stop. 

When you have captured the data you want to save, open the Transfer menu and 
choose Capture Text. On the secondary menu, choose Stop.  

 

You have now captured, and saved the file to your PC. This file can now be used 
in analyzing the communications traffic on the line, and assist in determining 
communication errors. 

Содержание inRAx MVI56-CAS























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды