manualshive.com logo in svg

ProSoft Technology inRAx MVI56-CAS, Руководство пользователя

Поделиться
Скачать
ProSoft Technology inRAx MVI56-CAS Скачать руководство пользователя страница 35

Diagnostics and Troubleshooting 

MVI56-CAS 

♦

 ControlLogix Platform 

 

Teledyne CA Slave Module 

 

ProSoft Technology, Inc. 

Page 35 of 86 

December 26, 2007 
 

Tip: 

To determine the number of blocks transferred each second, mark the numbers 

displayed at a specific time. Then some seconds later activate the command again. 
Subtract the previous numbers from the current numbers and divide by the quantity of 
seconds passed between the two readings. 

Viewing Module Configuration 

Press 

[C] 

to view the Module Configuration screen. 

Use this command to display the current configuration and statistics for the 
module. 

Opening the Database Menu 

Press 

[D]

 to open the Database View menu. Use this menu command to view the 

current contents of the module's database. 

Viewing Version Information 

Press 

[V] 

to view Version information for the module. 

Use this command to view the current version of the software for the module, as 
well as other important values. You may be asked to provide this information 
when calling for technical support on the product. 

Values at the bottom of the display are important in determining module 
operation. The Program Scan Counter value is incremented each time a 
module's program cycle is complete. 

Tip: 

Repeat this command at one-second intervals to determine the frequency of 

program execution. 

Warm Booting the Module 

Caution: 

Some of the commands available to you from this menu are designed for 

advanced debugging and system testing only, and can cause the module to stop 
communicating with the processor or with other devices, resulting in potential data loss 
or other failures. Only use these commands if you are specifically directed to do so by 
ProSoft Technology Technical Support staff. Some of these command keys are not 
listed on the menu, but are active nevertheless. Please be careful when pressing keys 
so that you do not accidentally execute an unwanted command. 

Press 

[W] 

from the Main Menu to warm boot (restart) the module. This command 

will cause the program to exit and reload, refreshing configuration parameters 
that must be set on program initialization. Only use this command if you must 
force the module to re-boot. 

Содержание inRAx MVI56-CAS























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды