manualshive.com logo in svg

ProSoft Technology inRAx MVI56-CAS, Руководство пользователя

Поделиться
Скачать
ProSoft Technology inRAx MVI56-CAS Скачать руководство пользователя страница 38

MVI56-CAS 

♦

 ControlLogix Platform 

Diagnostics and Troubleshooting 

Teledyne CA Slave Module  

 

Page 38 of 86  

ProSoft Technology, Inc. 

December 26, 2007 

 

Viewing Data in Hexadecimal Format 

Press 

[H]

 to display the data on the current page in hexadecimal format. 

Viewing Data in ASCII (Text) Format 

Press 

[A]

 to display the data on the current page in ASCII format. This is useful 

for regions of the database that contain ASCII data. 

Starting the Data Analyzer 

Press 

[B]

 to start the data analyzer. After the key is pressed, all data transmitted 

and received on the currently selected port will be displayed. An example display 
is shown below: 

 

The Data Analyzer displays the following special characters: 

Character Definition 

[ ] 

Data enclosed in these characters represent data received on the port. 

< > 

Data enclosed in these characters represent data transmitted on the port. 

<R+> 

These characters are inserted when the RTS line is driven high on the port. 

<R-> 

These characters are inserted when the RTS line is dropped low on the port. 

<CS> 

These characters are displayed when the CTS line is recognized high. 

_TT_ 

These characters are displayed when the timing mark interval has been reached. 
This parameter is user defined. 

 

 

Stopping the Data Analyzer 

Press 

[S]

 to stop the data analyzer. Use this option to freeze the display so the 

data can be analyzed. To restart the analyzer, press 

[B]

. 

Содержание inRAx MVI56-CAS























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды