manualshive.com logo in svg

ProSoft Technology inRAx MVI56-CAS, Руководство пользователя

Поделиться
Скачать
ProSoft Technology inRAx MVI56-CAS Скачать руководство пользователя страница 12

MVI56-CAS 

♦

 ControlLogix Platform 

Start Here 

Teledyne CA Slave Module  

 

Page 12 of 86  

ProSoft Technology, Inc. 

December 26, 2007 

 

1.4 

Install the Module in the Rack 

If you have not already installed and configured your ControlLogix processor and 
power supply, please do so before installing the MVI56-CAS module. Refer to 
your Rockwell Automation product documentation for installation instructions. 

Warning: 

You must follow all safety instructions when installing this or any other 

electronic devices. Failure to follow safety procedures could result in damage to 
hardware or data, or even serious injury or death to personnel. Refer to the 
documentation for each device you plan to connect to verify that suitable safety 
procedures are in place before installing or servicing the device.  

After you have checked the placement of the jumpers, insert MVI56-CAS into the 
ControlLogix chassis. Use the same technique recommended by Rockwell 
Automation to remove and install ControlLogix modules. 

Warning: 

When you insert or remove the module while backplane power is on, an 

electrical arc can occur. This could cause an explosion in hazardous location 
installations. Verify that power is removed or the area is non-hazardous before 
proceeding. Repeated electrical arcing causes excessive wear to contacts on both the 
module and its mating connector. Worn contacts may create electrical resistance that 
can affect module operation. 

1 

Turn power OFF. 

2 

Align the module with the top and bottom guides, and slide it into the rack 
until the module is firmly against the backplane connector.  

 

 

Содержание inRAx MVI56-CAS























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды