manualshive.com logo in svg

ProSoft Technology inRAx MVI56-CAS, Руководство пользователя

Поделиться
Скачать
ProSoft Technology inRAx MVI56-CAS Скачать руководство пользователя страница 27

Installing and Configuring the Module 

MVI56-CAS 

♦

 ControlLogix Platform 

 

Teledyne CA Slave Module 

 

ProSoft Technology, Inc. 

Page 27 of 86 

December 26, 2007 
 

Status Object (CASInStat) 

This object views the status of the module. The 

CASInStat

 object shown below 

is updated each time a read block is received by the processor. Use this data to 
monitor the state of the module at a "real-time rate". 

 

Refer to the Reference chapter for a complete listing of the data stored in this 
object. 

2.1.4  User Data Objects 

These objects hold data to be transferred between the processor and the MVI56-
CAS module. The user data is the read and write data transferred between the 
processor and the module as "pages" of data up to 200 words long. 

 

The read data (

ReadData

) is an array set to match the value entered in the 

ReadRegCnt

 parameter of the 

CASModule

 object. For ease of use, this array 

should be dimensioned as an even increment of 200 words. This data is paged 
up to 200 words at a time from the module to the processor. The ReadData task 
is responsible for placing the data received into the proper position in the read 
data array. Use this data for status and control in the ladder logic of the 
processor. 

Содержание inRAx MVI56-CAS























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды