manualshive.com logo in svg

ProSoft Technology inRAx MVI56-CAS, Руководство пользователя

Поделиться
Скачать
ProSoft Technology inRAx MVI56-CAS Скачать руководство пользователя страница 26

MVI56-CAS 

♦

 ControlLogix Platform 

Installing and Configuring the Module 

Teledyne CA Slave Module  

 

Page 26 of 86  

ProSoft Technology, Inc. 

December 26, 2007 

 

The BPFail parameter determines if the module should continue communicating 
on the TCA network when the backplane transfer operation fails. A value of zero 
indicates that the module should continue communicating when the backplane is 
not operational. If the value is greater than zero, the backplane will be retried the 
entered number of times before a failure will be reported and communication will 
cease on the ports. When backplane communication is restored, the module will 
start communicating on the network. For example, if you enter a value of 10 for 
the parameter, the module will stop all TCA communications if 10 successive 
backplane errors are recognized. When a successful transfer is recognized, the 
module will resume communications on the network. 

TCA Port Parameters (CASPort) 

 

This object defines the parameters for the operation of each of the TCA ports on 
the module. Refer to the Reference chapter for the definition of each parameter. 

Содержание inRAx MVI56-CAS























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды