manualshive.com logo in svg

ProSoft Technology inRAx MVI56-CAS, Руководство пользователя

Поделиться
Скачать
ProSoft Technology inRAx MVI56-CAS Скачать руководство пользователя страница 16

MVI56-CAS 

♦

 ControlLogix Platform 

Start Here 

Teledyne CA Slave Module  

 

Page 16 of 86  

ProSoft Technology, Inc. 

December 26, 2007 

 

Note: 

If the list of configured drivers is blank, you must first choose and configure a 

driver from the Available Driver Types list. The recommended driver type to choose for 
serial communication with the processor is "RS-232 DF1 Devices".  

3 

Click to select the driver, and then click Configure. This action opens the 
Configure Allen-Bradley DF1 Communications Device dialog box. 

 

4 

Click the Auto-Configure button. RSLinx will attempt to configure your serial 
port to work with the selected driver.  

5 

When you see the message "Auto Configuration Successful", click the OK 
button to dismiss the dialog box.  

Note: 

If the auto-configuration procedure fails, verify that the cables are connected 

correctly between the processor and the serial port on your computer, and then try 
again. If you are still unable to auto-configure the port, refer to your RSLinx 
documentation for further troubleshooting steps.  

Содержание inRAx MVI56-CAS























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды