Promise Technology FastTRAK66 Скачать руководство пользователя страница 58 | Manualshive

Страница: 58 / 73

background image

Chapter 8

Troubleshooting & T ips

The following chapter is used to assist with troubleshooting conflicts and Fast-
Trak66 installation problems. Also refer to the “README.TXT” file on the Fast-
Trak66 driver and utility diskette for more recent information as well as the

PromiseOnline

TM

services listed in Appendix A.

Eliminate Master/Slave combination problems

Freeing additional IRQ resources

Configuring PCI IRQ Assignment

Set Mainboard CMOS Boot sequence

Mainboard CMOS displays C: or D: drive failure during startup

Coexist with IDE hard drives

Drive cannot be formed into an array

Critical Status Error during boot

System locks up during bootup or when Windows starts

Intermittent data problems

Different drive lettering under Windows NT

Promise Windows95/98 driver does not appear Device Manager

Tips for Audio/Video Editing

Eliminate Master/Slave combination problems

Master/slave problems may exist between two IDE drives of different brands at-
tached to a single cable. For both compatibility and better performance, choose
drives of the same model/brand and install them on separate cables. Refer to the
Drive Setup by Connector chart in Chapter 4 for more recommended drive place-
ments.

Freeing additional IRQ resources

Since the Promise card supports PCI Interrupt sharing, it is possible to use IRQs
already assigned to another PCI card. Interrupt Sharing is not supported with onboard
IDE controllers. If the onboard IDE controller(s) are not used, you may disable the
controllers to free IRQ 14 and/or 15.

8-1

«
...
56
57
58
59
60
...
»

Содержание FastTRAK66










































































Отзывы:

Нет отзывов

Похожие инструкции для FastTRAK66

Бренд: ABB Страницы: 2

Бренд: jbc Страницы: 4

Бренд: NEC Страницы: 304

Бренд: Federal Signal Corporation Страницы: 60

Бренд: FASTRON. Страницы: 16

Бренд: Laars Страницы: 28

Бренд: Pando Страницы: 43

Бренд: YOKOGAWA Страницы: 150

Бренд: YOODA Страницы: 3

Бренд: YMGI Страницы: 8

DuetPro Carrycot

Бренд: Qtus Страницы: 52

Бренд: Fox Страницы: 5

Бренд: GEA Страницы: 13

Бренд: Viva Страницы: 9

Entelli-Switch 250

Бренд: GE Страницы: 32

Ratio Feeder J+ Advanced Series

Бренд: H.E. Anderson Страницы: 11

Бренд: CAME Страницы: 128

SUPERSEAL 2014 Series

Бренд: APV Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды