Promise Technology FastTRAK66 Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 73

background image

Quick Installation

Quick Installation

This section is designed to get you started for quick installation of your FastTrak66.

Use drives that are preferably the same model and capacity.

NOTE:

If using older

IDE drives (less than 300MBs), check with the manufacturer if it supports Multi-
DMA transfers.

[ 1 ] Install FastTrak66

and Drives

Power off the system and ground yourself by touching exposed metal of the PC
chassis.

Connect 18” 80-wire/40-pin cables to the FastTrak66 and hard disk drives. Make

sure the blue plastic connector is used for
the FastTrak66 slots. Attach the darker con-
nectors to the drives. Note that the colored
cable edge indicates Pin 1.

Jumper and install the drives with proper
mas-

ter/slave jumper settings recommended by
the drive manufacturer. When 2 drives are
attached, configure each drive as a master
(with no slave attached) and each drive on
a separate channel. Check drive instruc-
tions for details on Master & Slave settings.

Attach the case LED 2-pin or 4-pin cable

to the FastTrak66 4-pin
power/ground connector labeled LED. Be sure to align pin 1 of the
LED cable to pin 1 of the connector.

Insert and secure the FastTrak66 into an open PCI slot. Re-check

cabling for proper connection.

LED

1

----
M
M
M & S

Total Drives

IDE 1

IDE 2

One
Two
Three
Four

M
M
M & S
M & S

FastTrak66 Drive Setup

2-2

«
...
9
10
11
12
13
...
»

Содержание FastTRAK66










































































Отзывы:

Нет отзывов

Похожие инструкции для FastTRAK66

Бренд: CAME Страницы: 98

Бренд: CAME Страницы: 16

Бренд: CAME Страницы: 8

Бренд: Jedo Страницы: 26

VARIVENT D Series

Бренд: GEA Страницы: 78

Бренд: GEA Страницы: 96

Бренд: GEA Страницы: 66

Бренд: UNI Страницы: 21

Бренд: OBSIDIAN CONTROL SYSTEMS Страницы: 13

Бренд: Harman Kardon Страницы: 25

Бренд: Uniss Страницы: 21

Бренд: WAREMA Страницы: 112

Бренд: WAGO Страницы: 414

Бренд: V2 Страницы: 48

Бренд: Waterway Страницы: 8

JetWeb JX2-PRN1

Бренд: Jetter Страницы: 25

Бренд: Daikin McQuay Страницы: 8

Бренд: Mitsubishi Страницы: 30

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды