Pro Mach Orion CTS Flex Stretchwrapper Скачать руководство пользователя страница 95

Страница: 95 / 132

Orion

Machine Manual

Revision 3.0

CTS Flex Stretchwrapper

25 July 2016

Troubleshooting

Page 4-11

Film Feed / Stretch Functions

No Power Feed

Motor failure.

Perform motor test per motor manufac-

turer's recommendations.

Replace Motor as needed.

Film Feed Runs Or Creeps

Continuously

MIB values at the touchscreen are

out of calibration.

Observe the feedback value of the hall

effect located on the touchscreen.

Re-set the ZERO and GAIN values

according to the film feed setup instruc-

tions in the manual. ZERO setting should

be a value of at least ten above the hall

effect feedback value to operate properly.

Hall effect device is positioned

incorrectly.

Check to make sure hall effect device is

not touching the dancer bar cam.

Adjust the hall effect-to-cam gap is cor-

rect… approx 16th of an inch gap.

Dancer bar cam is positioned

incorrectly.

Make sure the cam rotates in such a way

as to create a gap between the hall effect

device and the cam itself.

Adjust the cam correctly.

Hall effect device has failed

Perform tests mentioned above.

If this does not resolve the issue, replace

the hall effect device.

Minimum speed setting on the

VFD is incorrect.

Review the minimum frequency parame-

ter settings in the VFD. Refer to the sup-

plied VFD Manual for procedure.

Refer to the VFD manual and the Orion

parameter settings sheet supplied with the

machine for minimum frequency settings.

Film Breakage Issues

Film Breaks Inside The

Carriage (Usually Between The

Rubber Stretch Rollers)

Incorrect gauge / type film is

being used for the application.

Review the film's stretch capability. The

film used should be able to effectively

stretch 280% at ambient temperatures.

Remove any film that does not comply

with the machine's requirements or,

change the stretch sprocket on the

machine to stretch below the film's fatigue

value.

Film is damaged.

Observe the edges and sides of the roll for

damage from handling.

Replace improper film with film in good

condition.

Table 4-1. Troubleshooting Chart (Continued)

PROBLEM

POSSIBLE CAUSE

SOLUTION

Содержание Orion CTS Flex Stretchwrapper





































































































































Результаты поиска

Содержание Orion CTS Flex Stretchwrapper

Отзывы:

Похожие инструкции для Orion CTS Flex Stretchwrapper

Бренды по названию

Популярные бренды

Pro Mach Orion CTS Flex Stretchwrapper, Руководство пользователя

Результаты поиска

Содержание Orion CTS Flex Stretchwrapper

Отзывы:

Похожие инструкции для Orion CTS Flex Stretchwrapper

Бренды по названию

Популярные бренды