Pro Mach Orion CTS Flex Stretchwrapper Скачать руководство пользователя страница 89

Страница: 89 / 132

Orion

Machine Manual

Revision 3.0

CTS Flex Stretchwrapper

25 July 2016

Troubleshooting

Page 4-5

Turntable / Tower Will Not

Rotate

No control Power / E-Stop Condi-

tion.

E-Stop button is Flashing or Green Start

button is not illuminated.

Perform E-Stop Reset (pull E-Stop button

to the out position then press the Green

Start button so that it is Illuminated. Press

Cycle reset on the Touchscreen.

Machine is in Cycle Pause.

Observe the Cycle Pause Icon on the Run

Screen. If it is illuminated, the machine is

in a Pause state.

Press Resume to resume wrapping.

VFD parameter settings are incor-

rect.

Review the parameter settings in the VFD.

Refer to the supplied VFD Manual for

procedure.

Refer to the VFD manual and the Orion

parameter settings sheet supplied with the

machine for maximum frequency settings.

Blown Fuse.

Locate Table / Tower rotation control

fuse. Remove fuse and check continuity.

Bad Fuse? Replace with correct type.

VFD Error.

Check the status of the table / tower motor

controller (VFD) for error message.

Refer to the VFD manual supplied with

the machine for error messaging solutions.

Open circuit to the motor.

Check wire continuity from VFD to

Motor.

Repair or replace open wiring.

Motor Failure.

Perform motor test per motor manufac-

turer's recommendations.

Replace Motor as needed.

Table 4-1. Troubleshooting Chart (Continued)

PROBLEM

POSSIBLE CAUSE

SOLUTION

Содержание Orion CTS Flex Stretchwrapper





































































































































Результаты поиска

Содержание Orion CTS Flex Stretchwrapper

Отзывы:

Похожие инструкции для Orion CTS Flex Stretchwrapper

Бренды по названию

Популярные бренды

Pro Mach Orion CTS Flex Stretchwrapper, Руководство пользователя

Результаты поиска

Содержание Orion CTS Flex Stretchwrapper

Отзывы:

Похожие инструкции для Orion CTS Flex Stretchwrapper

Бренды по названию

Популярные бренды