Pro Mach Orion CTS Flex Stretchwrapper Скачать руководство пользователя страница 91

Страница: 91 / 132

Orion

Machine Manual

Revision 3.0

CTS Flex Stretchwrapper

25 July 2016

Troubleshooting

Page 4-7

Carriage Lift

(Up & Down)

Carriage Will Not Move Up Or

Down (In Either Manual Mode

Or During An Auto Wrap

Cycle)

A False (No visible obstruction)

lift belt error has occurred.

Remove upper-rear access panel on the

back of the mast. Observe the position of

the lift belt roller switch at the top, inside

of the mast. The belt should be between

the metal frame and the switch's roller

lever. The lever roller should be activated.

If the belt is placed incorrectly, re-set belt

so that it is between the frame and the

switch's lever roller. The switch may need

to be re-positioned as to not give a false

signal.

Current Limiter in the carriage lift

VFD is activating.

Check for a mechanical bind in the car-

riage lift mechanicals, such as, worn belt

wheel bearings incorrectly aligned belt or

carriage safety cam-locks.

Identify and repair or replace worn parts.

Maximum speed setting on the

VFD is incorrect.

Review the maximum frequency parame-

ter settings in the VFD. Refer to the sup-

plied VFD Manual for procedure.

Refer to the VFD manual and the Orion

parameter settings sheet supplied with the

machine for maximum frequency settings.

Machine's supply voltage is too

low.

Check AC voltage (at the On-Off switch

terminals) while the machine is running

under load.

If voltage drops below 115, the supply is

not strong enough to run the machine cor-

rectly. Contact plant electrician. Do not

use household extension cords with the

machine.

Loose connections in the carriage

lift circuit.

Remove power from machine. Check for

loose connections in the carriage lift cir-

cuit such as; Primary supply to the Lift

VFD, Secondary supply from the VFD to

the drive motor and all connections in

between.

Re-seat all loose connections. Tighten

connections correctly.

Table 4-1. Troubleshooting Chart (Continued)

PROBLEM

POSSIBLE CAUSE

SOLUTION

Содержание Orion CTS Flex Stretchwrapper





































































































































Результаты поиска

Содержание Orion CTS Flex Stretchwrapper

Отзывы:

Похожие инструкции для Orion CTS Flex Stretchwrapper

Бренды по названию

Популярные бренды

Pro Mach Orion CTS Flex Stretchwrapper, Руководство пользователя

Результаты поиска

Содержание Orion CTS Flex Stretchwrapper

Отзывы:

Похожие инструкции для Orion CTS Flex Stretchwrapper

Бренды по названию

Популярные бренды