Pro Mach Orion CTS Flex Stretchwrapper Скачать руководство пользователя страница 36

Страница: 36 / 132

Machine Manual

Orion

CTS Flex Stretchwrapper

Revision 3.0

System Operation

25 July 2016

Page 3-6

Press this button to wrap the load again. The same wrap parameters are used.

Press this button to index the load to the exit conveyor. This button is available on

certain machine configurations when the machine is reset.

Press this button to apply the predefined reinforce-

ment wraps to the load. If the Reinforcement Wraps

value is set to zero, reinforcement wraps will be

applied as long as the Reinforce button is pressed.

REINFORCING

Press this button to stop the current wrap cycle.

Press this button to reset the current fault condition.

Press this button to toggle between High Speed and Low Speed operation. When

High Speed is selected, the Main Drive will travel at the predefined High Speed

value during the wrap cycle. When Low Speed is selected, the Main Drive will

travel at the predefined Low Speed value during the wrap cycle.

Press this button to send the machine to its Home Position. When pressed, the Car-

riage will travel to its bottom limit, and the Main Drive will travel to its predefined

End of Cycle Position.

Table 3-2. The Run Screen Button Descriptions (Continued)

STATE 1

DESCRIPTION

STATE 2

Содержание Orion CTS Flex Stretchwrapper





































































































































Результаты поиска

Содержание Orion CTS Flex Stretchwrapper

Отзывы:

Похожие инструкции для Orion CTS Flex Stretchwrapper

Бренды по названию

Популярные бренды

Pro Mach Orion CTS Flex Stretchwrapper, Руководство пользователя

Результаты поиска

Содержание Orion CTS Flex Stretchwrapper

Отзывы:

Похожие инструкции для Orion CTS Flex Stretchwrapper

Бренды по названию

Популярные бренды