Pro Mach Orion CTS Flex Stretchwrapper Скачать руководство пользователя страница 82

Страница: 82 / 132

Machine Manual

Orion

CTS Flex Stretchwrapper

Revision 3.0

System Operation

25 July 2016

Page 3-52

LOW AIR PRESSURE

The machine pneumatic pressure is low.

Check the pneumatic supply.

Ensure 80 PSI is available.

BRUSH AND CUTTER

NOT HOME

The brush and cutter are not home.

Cycle the brush and cutter.

Check why the brush and cutter

can’t reach the home position.

OBSTACLE DETECTED

The tower has an obstruction.

Check for a mechanical bind.

Clear the cause of the fault.

Reset and restart, when ready.

MULTISTRETCH VFD

NOT READY

The indicated VFD is not ready to run.

Check the fault code on the VFD

display in the electrical cabinet.

See VFD manual for fault code

information.

MAIN DRIVE VFD NOT

READY

CARRIAGE VFD NOT

READY

(NAME) CONVEYOR

VFD NOT READY

X2X

COMMUNICATION

ERROR

There is an X2X communication fault, press and

release the E-stop button to clear the fault.

Contact Orion Packaging if

problem persists.

RS485

COMMUNICATION

ERROR

There is an RS485 communication fault, press

and release the E-stop button to clear the fault.

Contact Orion Packaging if

problem persists.

Table 3-33. The Information and Alarm Displays (Continued)

MESSAGE

DESCRIPTION

CORRECTION

Содержание Orion CTS Flex Stretchwrapper





































































































































Результаты поиска

Содержание Orion CTS Flex Stretchwrapper

Отзывы:

Похожие инструкции для Orion CTS Flex Stretchwrapper

Бренды по названию

Популярные бренды

Pro Mach Orion CTS Flex Stretchwrapper, Руководство пользователя

Результаты поиска

Содержание Orion CTS Flex Stretchwrapper

Отзывы:

Похожие инструкции для Orion CTS Flex Stretchwrapper

Бренды по названию

Популярные бренды