Pro Mach Orion CTS Flex Stretchwrapper Скачать руководство пользователя

Страница: 93 / 132

Orion

Machine Manual

Revision 3.0

CTS Flex Stretchwrapper

25 July 2016

Troubleshooting

Page 4-9

Carriage Is Jammed At The
Top Of The Mast. (Carriage

Will Not Move Up Or Down)

Carriage bottom travel switch did

not activate correctly, possibly

sticking.

Belt is tangled around drum. Belt is

wrapped backwards or twisted.

Check switch by manually activating

(wiggling) the roller tip. If the switch does

not activate and release it's input on the

PLC correctly, replace the switch. The belt

will need to be removed and re-wound

correctly. The carriage will need to be

brought down manually. Refer to the

"Carriage Obstacle Detect Error Recov-

ery" inset in your manual.

Carriage bottom travel striker is

set too low for switch to activate

properly.

Belt is tangled around drum. Belt is

wrapped backwards or twisted.

Raise the bottom limit striker so that the

carriage travel switch activates it's PLC

input before the carriage physically hits

the machine's framework. The belt will

need to be removed and re-wound cor-

rectly. The carriage will need to be

brought down manually. Refer to the

"Carriage Obstacle Detect Error Recov-

ery" inset in your manual.

Film Feed / Stretch Functions

No Power Feed

No control -power / E-Stop condi-

tion.

E-Stop button is flashing or green start

button is not illuminated

Perform E-Stop reset sequence.

1. Reset all safety's (close carriage door,

latch carriage safety switch bar [RT only].

2. Pull E-Stop to the OUT position.

3. Press Green Start Button.

4. Press Cycle Reset button on screen.

Film is threaded incorrectly.

Compare film with threading diagram on

top of carriage.

Re-thread film carriage.

VFD parameter settings are

incorrect .

Review the parameter settings in the VFD.

Refer to the supplied VFD Manual for

procedure.

Refer to the VFD manual and the Orion

parameter settings sheet supplied with the

machine for maximum frequency settings.

Table 4-1. Troubleshooting Chart (Continued)

PROBLEM

POSSIBLE CAUSE

SOLUTION

Содержание Orion CTS Flex Stretchwrapper





































































































































Результаты поиска

Содержание Orion CTS Flex Stretchwrapper

Отзывы:

Похожие инструкции для Orion CTS Flex Stretchwrapper

Бренды по названию

Популярные бренды

Pro Mach Orion CTS Flex Stretchwrapper, Руководство пользователя

Результаты поиска

Содержание Orion CTS Flex Stretchwrapper

Отзывы:

Похожие инструкции для Orion CTS Flex Stretchwrapper

Бренды по названию

Популярные бренды