Pro Mach Orion CTS Flex Stretchwrapper Скачать руководство пользователя страница 79

Страница: 79 / 132

Orion

Machine Manual

Revision 3.0

CTS Flex Stretchwrapper

25 July 2016

System Operation

Page 3-49

CLAMIPING &

CUTTING FILM

The machine is now in the clamp and cut cycle.

This is for informational pur-

poses only. No correction neces-

sary.

INITIALIZING

The machine is initializing.

There is a brief initialization

sequence once the machine is

reset. Allow the machine to ini-

tialize prior to starting.

LIGHT CURTAIN

BLOCKED

The light curtain is blocked (if equipped.)

Clear the obstruction from the

light curtain to allow operation.

SAFETY SYSTEM NOT

READY

The safety controller is not ready to run.

Allow the safety system to ini-

tialize prior to running.

FAULTS EXIST

Faults currently exist.

Correct the cause of the fault.

Press reset to reset the fault con-

dition once the cause is cor-

rected.

CARRIAGE MOVING

UP TOO SLOWLY

The carriage is moving upward too slowly.

Check for the cause of the car-

riage not moving correctly.

Check the belt drive behind the

back panel. Check for a jam or

obstruction on the track.

CARRIAGE MOVING

DOWN TOO SLOWLY

The carriage is moving downward too slowly.

Check for the cause of the car-

riage not moving correctly.

Check the belt drive behind the

back panel. Check for a jam or

obstruction on the track.

BRUSH AND CUTTER

NOT HOME

The brush and cutter are not home.

Cycle the brush and cutter.

Check why the brush and cutter

can’t reach the home position.

MULTISTRETCH VFD

NOT READY

The indicated VFD is not ready to run.

Check the fault code on the VFD

display in the electrical cabinet.

See VFD manual for fault code

information.

MAIN DRIVE VFD NOT

READY

CARRIAGE VFD NOT

READY

Table 3-32. The Information and Alarm Displays (Continued)

MESSAGE

DESCRIPTION

CORRECTION

Содержание Orion CTS Flex Stretchwrapper





































































































































Результаты поиска

Содержание Orion CTS Flex Stretchwrapper

Отзывы:

Похожие инструкции для Orion CTS Flex Stretchwrapper

Бренды по названию

Популярные бренды

Pro Mach Orion CTS Flex Stretchwrapper, Руководство пользователя

Результаты поиска

Содержание Orion CTS Flex Stretchwrapper

Отзывы:

Похожие инструкции для Orion CTS Flex Stretchwrapper

Бренды по названию

Популярные бренды