Pro Mach Orion CTS Flex Stretchwrapper Скачать руководство пользователя

Страница: 41 / 132

Orion

Machine Manual

Revision 3.0

CTS Flex Stretchwrapper

25 July 2016

System Operation

Page 3-11

CARRIAGE DOWN

SPEED

Press this button to change the speed of the carriage on the downward move, in

terms of percentage. Min - 5% Max - 100%

WRAP BOTTOM FIRST

Press this button to select the Wrap Bottom First wrap sequence. When selected, the

wrapper will apply the bottom wraps first. When complete, the Carriage will travel

to the top of the load and apply the top wraps. When complete, the Carriage will

travel to the bottom and complete the cycle.

WRAP TOP FIRST

Press this button to select the Wrap Top First wrap sequence. When selected, the

Carriage will immediately travel to the top of the load and apply the top wraps.

When complete, the Carriage will travel to the bottom, apply the bottom wraps, and

complete the cycle.

WRAP UP ONLY

Press this button to wrap up only. The machine will wrap to the top, then stop the

cycle.

LOW SPEED SELECTED

Press this button to toggle between High Speed and

Low Speed operation. When High Speed is selected,

the Main Drive will travel at the predefined High

Speed value during the wrap cycle. When Low

Speed is selected, the Main Drive will travel at the

predefined Low Speed value during the wrap cycle.

HIGH SPEED

SELECTED

UNSTABLE LOAD

DISABLED

Press this button to enable or disable the Unstable

Load wrap cycle. When enabled, the Main Drive will

travel at Low Speed until the wrapper has completed

one top wrap. After one top wrap is completed, the

Main Drive will travel at High Speed for the remain-

der of the cycle. If Low Speed is selected, the Main

Drive will travel at Low Speed for the entire cycle.

UNSTABLE LOAD

ENABLED

AUTOHEIGHT

DISABLED

Press this button to enable or disable the Autoheight

photoeye. When enabled, the Carriage will travel up,

during the wrap cycle, until the Autoheight photoeye

no longer sees a load. It will continue to travel until

the Autoheight Delay time is complete. When dis-

abled, the Carriage will travel up, during the wrap

cycle, until it reaches the Top Limit sensor.

AUTOHEIGHT

ENABLED

FILM FAULT DISABLED

Press this button to enable or disable the End of Roll

or Broken Film fault. When disabled, the wrap cycle

will continue even if the film has broken or there is

no film left on the roll.

FILM FAULT ENABLED

Table 3-6. The Wrap Settings Screen Button Descriptions (Continued)

STATE 1

DESCRIPTION

STATE 2

Содержание Orion CTS Flex Stretchwrapper





































































































































Результаты поиска

Содержание Orion CTS Flex Stretchwrapper

Отзывы:

Похожие инструкции для Orion CTS Flex Stretchwrapper

Бренды по названию

Популярные бренды

Pro Mach Orion CTS Flex Stretchwrapper, Руководство пользователя

Результаты поиска

Содержание Orion CTS Flex Stretchwrapper

Отзывы:

Похожие инструкции для Orion CTS Flex Stretchwrapper

Бренды по названию

Популярные бренды